781987
42
Zoom out
Zoom in
Previous page
1/48
Next page
Seite:42
TROUBLESHOOTING
To repair disfunctiones switch off the machine. Pull out power supply.
Cause Remedy
Upon switching off the saw does not slow down.
Brake board defect Renew brake board
Electrotechnical maintenance works should only be carried out by an electronics technician!
On removal of the machine the local legal regulations have to be abided by.
Fehlersuche Benzinmotor
Störung Mögliche Ursache Abhilfe
Saw blade comes loose
after the engine is
turned off.
1. Mounting nut has not been sufficiently tightened. 1. Tighten the mounting nut; right-hand thread.
Burnt areas on the
cutting surface
1. Blunt saw blade
2. Incorrect saw blade
1. Sharpen the saw blade, replace it.
2. Replace the saw blade
Engine does not start 1. The spark plug cable has been disconnected.
2. No fuel or old fuel.
3. The choke is not in the open position
4. The fuel line is blocked.
5. Dirty spark plug.
6. The engine has stalled.
7. The engine oil level is low.
1. Connect the spark plug cable securely to the
spark plug
2. Put in clean, fresh petrol.
3. The throttle lever has to be in the CHOKE posi-
tion during cold start.
4. Clean the fuel line.
5. Clean, set gap or replace.
6. Wait a few minutes before restarting, but do not
let the engine draw in petrol.
7. The oil monitor prevents the engine starting if
the oil level is low - check the oil level.
The engine runs irre-
gularly.
1. The spark plug cable is loose.
2. The engine runs with CHOKE.
3. The fuel line is blocked or old fuel is in the
tank.
4. The ventilation hole is blocked.
5. There is water or contamination in the fuel
system.
6. Dirty air filter.
7. Incorrect carburettor setting.
1. Connect the spark plug cable and secure it.
2. Turn the choke lever to OFF.
3. Clean the fuel line. Fill the tank with clean,
fresh petrol.
4. Clear the ventilation hole.
5. Empty the tank. Fill the tank with fresh fuel..
6. Clean or replace the air filter.
7. Contact the Service Department.
The engine has overhe-
ated.
1. The engine oil level is low.
2. Dirty air filter.
3. The air flow is restricted.
4. The carburettor is not set correctly.
1. Fill the crankcase with the correct oil.
2. Clean the air filter.
3. Remove the casing and clean it.
4. Contact the Service Department
42


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach WOX Z 700SL at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach WOX Z 700SL in the language / languages: English, German, French as an attachment in your email.

The manual is 4.29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info