Manual Scheppach WDS 999 Kraft Werkzeuge (page 21 of 36) (English, German, French)

781891

Zoom out

Zoom in

1/36

21 І 36

8.4.Connection for dust extractor (g. 1, 5, 6)

m WARNING! Harmfull noxious gases may be gen-

erated when e.g. lead-containing paint is processed.

These gases entail a risk for the operator and the per-

sons in the vicinity! Therefore only use the power tool

in combination with a dust extraction unit, and protect

yourself and other persons in the working area with

additional suitable personal protective equipment!

When working with this power tool, a Iot of dust is

generated. The dust extraction unit is very useful if

you want to keep your workplace clean. lt is possible

to combine the extraction system or a vacuum cleaner

with the extraction hose (14) which is connected to

the adapter for dust extraction.

Insert the hose adaptor (15) into the connection for

dust extraction (10 or 12) and lock it by twisting as

shown in g. 5 and 6.

Note: Connect your tool to an extraction unit or vac-

uum cleaner. This will provide excellent extraction of

dust and debris.

m ATTENTION! For health safety reasons it is im-

perative that you use a dust extractor.

Note: Make sure that the vacuum cleaner is suitable

for being used together with a power tool.

8.5. Function of the brushed edge (g.7)

The grinding head of this power tool is enclosed by

a brush edge (A) which offers the following two ad-

vantages:

a) The brush edge (A) protrudes beyond the grind-

ing plate (1) and touches the surface to be pro-

cessed rst. Thus, the grinding plate is posi-

tioned in parallel to the working area before the

insertion tool comes in contact with the surface

which is to be processed. This is to prevent the

formation of sickle-shaped recesses caused by

the grinding disk edge.

b) Furthermore, the brush edge (A) prevents the

generation of excessive dust. Dust generated du

ring the grinding process is not transported to-

wards the outside but is removed by the extraction

system. Make sure before each operation with

this power tool that the brush edge (A) is not dam-

aged. Have it replaced if there is damage or wear.

8.6. Connection to the power supply

1. Make sure that the power tool is switched off.

2. Plug the power plug into a correctly installed

socket which complies with the requirements

specied in the technical data.

3. Your power tool is now ready for operation.

8.7. Switching on/off (g.8)

To switch on:

Push the on/ off switch (13)

Continuous operation: (g.8)

Secure the on/off switch (13) with the locking knob (6).

To switch off:

Press the on/off switch (13) briey and let go.

8.8. Adjusting the oscillation rate (g.9)

Before you start working, adjust the oscillation rate

according to the application. Use a low number of os-

cillations for rough grinding, increase the oscillation

rate for ne work.

• Rotate the adjustment wheel (5) to adjust the

oscillation rate. Turn the wheel clockwise to reduce

the oscillation rate (Fig.9).

• Turn the wheel counter-clockwise to increase the

oscillation rate (Fig. 9).

Note: The insertion tool moves for a short while after

having it switched off. Do not put aside the power tool

until the insertion tool has come to a complete halt.

8.9. Grinding

1. Attach an appropriate abrasive sheet (16) and

select the corresponding speed.

2. Hold the power tool securely at the handle sur-

faces (7, 2) and switch it on as described.

3. Wait until the insertion tool has reached its full

operating speed.

4. Hold the grinding plate (1) as parallelas possi-

ble to the wall, and touch the surface tobe pro-

cessed with the brush edge (A) rst.

5. Apply some pressure to the grinding head (1)

such that the insertion tool touches the surface

to be processed.

6. Constantly move the power tool over the surface.

Note: lf you want to avoid irregular grinding results,

do not keep the power tool at one spot for too long.

7. Lift the grinding plate (1) from the surface to be

processed before switching off the power tool.

8. Do not put aside the power tool until the insertion

tool has come to a complete halt.

8.10. After use

1. Switch off the power tool as described, discon-

nect it from the power supply and Iet it cool down.

2. Clean and maintain the power tool as described

under point 10, and store it carefully.

LED - light (g.10)

To ensure a well lit workplace, use the LED-light (4)

if necessary.

Press the switch (a) to switch ON/OFF the LED-light (4).

Ceiling grinding (g.11)

For working in ceiling area, x the grinding head with

a cotter pin (C) (included) as shown in gure 11.

9. Electrical connection

The electrical motor installed is connected and

ready for operation. The connection complies with

the applicable VDE and DIN provisions. The custom-

er‘s mains connection as well as the extension ca-

ble used must also comply with these regulations.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach WDS 999 Kraft Werkzeuge in the language / languages: English, German, French as an attachment in your email.

The manual is 2.29 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach WDS 999 Kraft Werkzeuge Manual

Product: