781487

Scheppach TS310 Manual

17
Zoom out
Zoom in
Previous page
1/212
Next page
17
m Remaining hazards
The machine has been built using modern technology in ac-
cordance with recognized safety rules. Some remaining haz-
ards, however, may still exist.
• The rotating saw blade can cause injuries to fingers and
hands if the work piece is incorrectly fed.
• Thrown work pieces can lead to injury if the work piece
is not properly secured or fed, such as working without
a limit stop.
• Noise can be a health hazard. The permitted noise level
is exceeded when working. Be sure to wear personal
protective gear such as ear protection.
• Defective saw blades can cause injuries. Regularly in-
spect the structural integrity of saw blades.
• The use of incorrect or damaged mains cables can lead
to injuries caused by electricity.
• The operating instructions supplied with the special
accessories must be observed and carefully read when
Scheppach special accessories are used.
• Even when all safety measures are taken, some remain-
ing hazards which are not yet evident may still be pre-
sent.
• Remaining hazards can be minimized by following the
instructions in “Safety Precautions“, “Proper Use“ and
in the entire operating manual.
Assembly
Important:
When unpacking, take care to locate all the small parts of the
machine supplied inside the carton box.
Fig. 1
Place the table top (1) onto a work bench after having
removed the packing pad a underneath the motor.
Fig. 1.1
Fasten the base leg (2) onto the table top using 2 hexagon
bolts M6 x 16, 2 washers 6 and 2 nuts M6. Tighten the
bolts slightly by hand.
• Tout autre genre d’utilisation est considéré comme non
conforme. Le constructeur n’assume pas de responsa-
bilité en cas de dommages dans ce cas; le risque est à
la charge de l’utilisateur seul.
m Risques résiduels
Cette machine est à la pointe de la technique et répond aux
règles de sécurité actuellement en vigueur. Néanmoins, cer-
tains risques résiduels peuvent survenir pendant son fonc-
tionnement.
• Risque de blessure aux doigts et aux mains au contact
de la lame rotative de la scie dû à un guidage inappro-
prié de la pièce à travailler.
• Blessures au contact de la pièce à travailler projetée en
raison d’un mauvais serrage ou d’un mauvais guidage,
en cas de travail sans butée par exemple.
• Risque pour la santé occasionné par le bruit. Pendant
le travail, le niveau sonore autorisé est dépassé. Il faut
impérativement porter des équipements de protection
personnels tels qu’une protection acoustique.
• Blessures occasionnées par une lame de scie défec-
tueuse. Contrôlez régulièrement l’intégrité de la lame
de la scie.
• Risque dû à l’électricité lors de l’utilisation de câbles
de raccordement électriques non conformes.
• De plus, des risques résiduels invisibles peuvent surve-
nir malgré toutes les précautions prises.
• Les risques résiduels peuvent être réduits si les „règles
de sécurité“ et l’ utilisation conforme aux prescriptions“
ainsi que le mode d’emploi sont respectés.
Montage et mise en place
Remarque!
Lors du déballage, vérifier que les petites pièces de la
machine figurent bien dans les parties intérieures de
l’emballage.
Fig. 1
Poser le plateau de table 1 sur un établi. (Retirer le
matériel d’emballage sous le moteur)
Fig. 1.1
Monter le pied de bâti sur le plateau de table en utilisant
2 vis à six pans creux M6 x 16, 2 rondelles 6 et 2 écrous
M6.
Serrer légèrement les vis à la main.
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach TS310 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach TS310 in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 8.85 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info