Manual Scheppach TS310 (page 13 of 212) (English, German, Dutch, Danish, French, Italian, Swedish, Norwegian, Finnish)

781487

Zoom out

Zoom in

1/212

• Always use a push-stick for longitudinal cuts

of narrow workpieces (less than 120 mm). The

push-stick must be used to prevent you from hav-

ing to work with your hands near the sawblade.

Stop the machine to repair a failure or remove pieces

of wood which have become jammed. Disconnect the

mains plug.

• Use the push stick or the feed lever for sliding the

wood, to guide it safely past the saw blade.

• Switch the machine off and pull power supply plug

when rectifying any malfunctions.

• The table insert must be renewed when the saw slot is

worn down. Pull power supply plug.

• Before the machine is put into operation it must be

connected to a dust extractor with a ﬂexible, non-ﬂam-

mable suction hose. The suction should switch on auto-

matically when the machine is switched on.

• When leaving the work place, switch the motor off. Pull

the power supply plug.

• Cut off the external power supply of the machine or

plant even if only minor changes of place are envisaged.

Properly reconnect the machine to the supply mains

before recommissioning.

• Connection and repair work on the electrical installation

may be carried out by a qualiﬁed electrician only.

• All protection and safety devices must be replaced after

completing repair and maintenance procedures.

Accessories

Only purchase accessories from your authorised special-

ised dealer.

m Use only as authorized

The machine corresponds to the valid EC guideline.

CE tested machines meet all valid EC machine guidelines as

well as all relevent guidelines for each machine.

• The machine has been built in accordance with state-

of-the-art standards and the recognized safety rules.

Nevertheless, its use may constitute a risk to life and

limb of the user or of third parties, or cause damage to

the machine and to other material property.

• The circular saw bench is constructed exclusively for

the sawing of wood. The required saw blade should be

inserted according to the cut type and the wood type

(solid wood, chip board or plywood).

• Le coin séparateur est un dispositif de protection im-

portant, qui guide la pièce et empêche que l’entaille

ne se referme derrière la lame, ce qui évite un retour

de pièce.

• Descendre le carter de protection sur la pièce lors de

chaque passe. Celui-ci doit se trouver à l’horizontale

au-dessus de la lame.

• Lors d’une coupe longitudinale d’une pièce – inférieure

à 120 mm – il est indispensable d’utiliser une tige de

poussée. L’utilisation de cette tige est nécessaire pour

éviter que les mains se trouvent à proximité de la lame

de scie.

• Utilisez un poussoir à bois ou une poignée-poussoir

pour pousser la pièce à usiner contre la lame de scie

en toute sécurité.

• Pour pallier à une cause de dérangement, arrêter la

machine, débrancher la prise.

• Si la lumière de passage de lame est détériorée, rem-

placer la partie rapportée. Retirer la prise.

• Avant d’être mise en service, la machine doit être rac-

cordée à une installation d’aspiration au moyen d’une

conduite d’aspiration ﬂexible et difﬁcilement inﬂam-

mable. L’aspiration doit s’enclencher automatiquement

lorsque la machine est mise en service.

• Lorsque l’on s’éloigne de l’emplacement de travail,

arrêter le moteur et débrancher la prise.

• Même pour des changements de place peu importants,

séparer la machine ou l’installation de toute alimenta-

tion en énergie venant de l’extérieur! Avant la remise en

service, rebrancher la machine sur le réseau!

• Les branchements et réparations de l’équipement élec-

trique ne doivent être effectués que par un spécialiste

de l’électricité.

• Une fois les travaux de réparation et de maintenance

achevés, tous les dispositifs de protection et de sécurité

doivent être remontés immédiatement.

Accessoires

A acheter uniquement auprès de votre revendeur spécia-

lisé.

m Utilisation conforme

La machine correspond aux normes en vigueur dans la Com-

munauté Européenne.

• La scie circulaire est déﬁnié en tant que machine semis-

tationnaire suivant pr EN 1870-1.

• Pour le transport, tenir fermement chaque extrémité du

plateau à deux mains et soulever l’ensemble.

• Si vous n’utilisez pas le support d’origine, la machine

doit être posée sur un support plane et stable. La hau-

teur de travail doit être au minimum de 800 mm.

• Le poste de travail se trouve à l’avant de la machine, à

gauche de la lame de scie.

• Aﬁn d’éviter les risques d’accident, aucun corps étran-

ger ne doit se trouver autour du poste de travail et aux

alentours de la machine.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach TS310 in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 8.85 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach TS310 Manual

Product: