782060
5
Zoom out
Zoom in
Previous page
1/28
Next page
6 deutsch english 7
Manufacturer:
Scheppach Maschinenfabrik GmbH & Co. KG
Günzburger Straße 69
D-89335 Ichenhausen / FRG
Dear customer,
we wish you a lot of enjoyment and success while working
with your new scheppach unit.
We recommend:
Read through the entire text before assembling and
beginning operation.
General Notes
Design and execution subject to change without notice.
Check all parts for possible shipping damage
after unpacking. The shipper must be informed
immediately if a complaint is to be led.
Claims made at later date will not be processed.
Check the delivery to make sure it is complete.
Familiarize yourself with the unit by reading the
instructions before operating.
Use only original scheppach parts for accessories as well
as for spare and expendable parts.
When ordering, state our item numbers as well as type
and model year of the unit.
Notes on safety
Observe the safety notes of your scheppach machine the
pusher slide is to be mounted on.
Be sure to use tools safely and precisely when
operating.
Safety devices may not be removed.
Assembly
For packaging reasons, your scheppach pusher slide is not
completely assembled.
tku/ts 315 GT, Fig. A1
Attach the mounting plates to the front and rear of the
table.
2 hex bolts each M8 x 20
2 washers each 8 in diameter.
Hex bolts should be hand-tightened only.
hf 3000/tfe 30, Fig. A2
Attach the mounting plates to the front and rear of the
table.
2 hex bolts each M8 x 20
2 washers each 8 in diameter.
Hex bolts should be hand-tightened only.
Screw in adjusting screw (1). The inner adjusting screw
rests on the shank of the screw bracket on table tops
without a rolled lower edge.
Guide tube Fig. B
Insert the guide tube with the fastening arms, press on
and tighten the retaining plate (1).
1 washer 8 in diameter
1 hex nut M8 self-tightening
0.5 mm play must remain between the fastening arms
and the retaining plate.
Fasten the fastening arms using a wing nut M8 and a
washer 8 in diameter on top of the retaining plate.
Adjust, Fig C
Allow the stop on the guide tube to catch. Pull out and
turn.
Push the empty slide table onto the guide tube and allow
the stop to catch again.
Adjust, Fig D
Align the slide table. Use the stop track as a ruler. The
slide table must move parallel to saw or millig table and
at the same height.
Check repeatedly and then tighten the hex bolts of the
mounting plates.
Adjust hf 3000/tfe 30
Bring the slide table to the same level using the adjusting
screws on the screw brackets (Fig. A2) on the front and
rear side of the table.
Check repeatedly and then tighten the hex bolts of the
mounting plates.
Assembling the switch on tk, tkh, tku, Fig. A1
Screw switch to switch plate. Screw the unit onto the
front mounting plate
2 cheese head screws M5 x 15
2 large washers A 5,3
2 hex. nuts M5
Final assembly tk, tkh, tku, ts315 GT, Fig. E
(1) Stop tube
(2) Adjusting bolt
(3) Stop track
Insert stop tube (1) in the pivoting drill hole of the slide
table.
Insert carriage bolt M8 x 65 from above and tighten with
washer by hand.
79510000 79540000
Delivery Package
Pusher table
assembly
Pusher table
assembly
Guide tube assembly Guide tube assembly
Front mounting
support assembly
Front mounting
support assembly
Rear mounting
support assembly
Rear mounting
support assembly
Stop tube assembly Stop tube assembly
Stop track Stop track
Accessory bag Clamping device
Operating
instructions Accessory bag
Bearing strip
Operating
instructions
Technical Data
Work piece
width max.
(mm) between
tool and stop
at 90° position
550 500
Pivoting area,
stop track 2 x 45 ° 2 x 45°
Fixed anchor
point 15° each 15° each
Max. clamping
range of the
clamping
device (mm)
105
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach TKU at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach TKU in the language / languages: All languages as an attachment in your email.

The manual is 1.59 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info