781685
20
Zoom out
Zoom in
Previous page
1/124
Next page
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
20 | GB
Angle measurer (Fig. 6)
-
         

height of the universal support. To do so, perform the
following steps:
First, clamp the tool into the device and insert the de-
vice on the universal support.
Then, hold the angle measurer with the desired angle
at the tool tip. Now, adjust the height of the universal
support in such a manner that the front end of the


in alignment with the tool tip.
Note: The values indicated on the angle measurer


Grinding (Fig. 7)

can be seen in the lateral direction. This is normal
        
grinding result.
Expert tip: New tools still show traces of the produc-
-

-

the vertical of the grinding stone, and the front side
as follows.

in the device on the universal support, turn on the
motor, and start the grinding process. Press the tool

and move it crosswise across the stone.
Please make sure that at least half the width of the
cutting edge comes into contact with the grinding

 

       
       
dealer.
The height of the Universal Support can be set ex-

Support.

Never sharpen against the direction of grinding! Oth-
erwise, the tool will cut into the leather!
Impregnate the leather disc using weak machine oil.

    
pressing the ground tool with circular movements on
the wheel.
󰀩
         



8. 


want to work with or against the direction of grind-


grind coarse tools, such as axes, it is recommended


the direction of grinding. This applies, for example, to
carving tools and knives. Please note that the grind-
-
tion of rotation.
Please check before each operation whether the sur-
face of the grinding stone is even. To do so, lower the


If required, trim uneven material using the 250 trim-
ming device.

surfaces.

Fill the water reservoir with water up to the marking.
The grinding stone becomes saturated with water.

Once the grinding process is completed, lower the
water reservoir to prevent the grinding stone from be-
ing in the water for an extended period of time.
-
ticles of steel and trimmed stone will accumulate and
compress in the reservoir.

place a magnet into the water.

The speed of the grindstone and of the leather disc
-
ler. The speed depends on the required result. For
grinding, a speed in the lower range is more suitable.
For stripping with the leather disc, a higher speed is
more suitable.

Lower the water container when working with the
leather disc at high speeds.
In order to maintain an even grinding speed with a
decreasing grindstone diameter, the speed can be

Grinding stone ø mm
(inch)
Idle-running speed
grinding stone 1/min
250 (10'') 90-100
230 (9'') 100-110
200 (8'') 110 -125
180 (7'') 125-150
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach TIGER 3000VS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach TIGER 3000VS in the language / languages: English, German, Dutch, French, Italian, Polish as an attachment in your email.

The manual is 8.71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info