Manual Scheppach TAB660 Kity (page 11 of 24) (English, German, French)

782105

Zoom out

Zoom in

1/24

english 9

Controls and features (Fig. 1.1)

1. Headstock

1A. Driver

1B. Face plate

2. Tailstock

2A. Tailstock tip

2B. Clamping handle

2C. Eccentric release handle

3. Tool rest

3A. Eccentric clamping

3B. Clamping handle

4. Drilling bed

5. Motor

5A. Lever

5B. Clamping handle

6. On/off switch

General Safety Notes

In these operating instructions we have marked the places

that have to do with your safety with this sign.

• Please pass on safety notes and instructions to all those

who work on the machine.

• Comply with all safety instructions and warnings on the

machine.

• Keep all safety instructions and warnings on the ma-

chine fully legible.

• Check all power supply lines. Do not use defective

lines.

• Make sure that the machine stands stable on ﬁrm

ground.

• Caution when working: There is a danger to ﬁngers,

hands and eyes.

• Keep children away from the machine when it is con-

nected to the power supply.

• When working on the machine, all safety mechanisms

and covers must be mounted.

• Operating personal must be at least 18 years of age.

Trainees must be at least 16 years of age, but may only

operate the machine under adult supervision.

• Persons working on the machine may not be diverted

from their work.

• The working space on the machine must be free of chips

and wood scrap.

• Wear only close-ﬁtting clothes. Remove rings, bracelets

and other jewelry.

• For the safety of long hair, wear a cap or hair net.

• Do not wear gloves.

• Wear goggles when working.

• Note the motor rotational direction – see electrical con-

nection.

• The safety mechanisms on the machine may not be re-

moved or rendered unusable.

• Cleaning, changing, calibrating, and setting of the ma-

chine may only be carried out when the motor is switched

off. Pull the power supply plug and wait for the rotating

tool to completely stop.

• Switch the machine off and pull power supply plug when

rectifying any malfunctions.

• Connection and repair work on the electrical installation

may be carried out by a qualiﬁed electrician only.

• All protection and safety devices must be replaced after

completing repair and maintenance procedures.

• Place the tool support as tightly as possible against the

work piece.

• The peripheral speed of wooden workpieces must not

exceed 30 m/s. Note spindle speed diagram!

• Provide work pieces with center bores before clamping

between pivots.

• Work large and imbalanced work pieces at a reduced

rotational speed; it may be necessary beforehand to cut

accordingly with a band saw.

• Before switching on the machine, check that the work-

piece is securely clamped.

• Remove the chuck key or spring dowel sleeve before

turning the machine on.

• Always close the belt cover.

• Work with three- or four-jaw chucks may only be carried

out with mounted jaw chuck shield.

• Never stop work pieces with the hand during run out.

Never take measurements on a rotating work piece.

• Work only with well sharpened tools.

• Always use both hands when using turning tool.

• Nicked tools may not be used.

• Note the correct rotational setting on the machine.

• When leaving the work place, switch the motor off. Pull

the power supply plug.

• Unplug the machine before moving, even if only slightly.

Correctly connect the machine to the electrical source

before operating again.

Proper use

• CE tested machines meet all valid EC machine guidelines

as well as all relevent guidelines for each machine.

• The machine must only be used in technically perfect

condition in accordance with its designated use and the

instructions set out in the operating manual, and only

by safety-conscious persons who are fully aware of the

risks involved in oerating the machine. Any functional

disorders, especially those affecting the safety of the

machine, sholud terefore be rectiﬁed immediately.

• The „scheppach wood turner“ has been constructed ex-

clusively for use with wood.

• Any other use exceeds authorization. The manufacturer

is not responsible for any damages resulting from unau-

thorized use; risk is the sole responsibility of the opera-

tor.

• The safety, work and maintenance instructions of the

manufacturer as well as the technical data given in the

calibrations and dimensions must be adhered to.

• Relevant accident prevention regulations and other, gen-

erally recognized safety-technical rules must also be ad-

hered to.

• The machine may only be used, maintained, and operat-

ed by persons familiar with it and instructed in its opera-

tion and procedures. Arbitrary alterations to the machine

release the manufacturer from all responsibility for any

resulting damages.

• The machine may only be used with original accessories

and tools made by the manufacturer.

Remaining hazards

The machine has been built using modern technology in ac-

cordance with recognized safety rules. Some remaining haz-

ards, however, may still exist.

• Only process selected woods without defects such as:

Branch knots, edge cracks, surface cracks. Wood with

such defects is prone to splintering and can be hazard-

ous.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach TAB660 Kity in the language / languages: English, German, French as an attachment in your email.

The manual is 2.37 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach TAB660 Kity Manual

Product: