782063
27
Zoom out
Zoom in
Previous page
1/116
Next page
27
Installation et changement de pinces pour fraises de défon-
ceuse
• Lorsduchangementdespincespourfraises,vousde-
vez débrancher votre machine et sélectionner la pince
qui s’adapte parfaitement au diamètre de votre queue
de fraise.
• Oterleréducteurdelumière,Fig.16.
• Bloquerl’arbreàl’aideduboutonquesesitueàla
base de l’arbre. Fig. 18.
• Dévisserl’écroudeserragedepinceàl’aidedelaclé
plate fournie. Fig. 17.
• Insérer ou retirer la pince (qui est sertie dans
l’écrou).
• Resserrerfermementl’écroudelapincetoutenmain-
tenant le blocage de l’arbre, et avant toute utilisation
s’assurer que la fraise est parfaitement maintenue en
bout d’arbre.
• Repositionnerleréducteurdelumièreàsonemplace-
ment initial.
• Ajusterleguideàvotreconvenanceàl’aidedesgra-
duations sur la table.
• Connectervotreaspirateurdecopeaux(aspirateurnon
fourni). Il est fortement conseillé de connecter un as-
pirateur (ou un système d’aspiration) à copeaux afin de
ne pas obstruer la lumière, afin de permettre un bon
refroidissement du moteur ainsi qu’une bonne avance
de la pièce de bois sur la table.
• Rebrancherlamachine.
Réglage du guide de toupillage
L’utilisation du guide de toupillage est obligatoire. Cha-
que travail doit être considéré séparément. A chaque
nouvelle utilisation, vous devez vous assurer de la bonne
installation des protecteurs et de leur bon réglage.
A chaque nouvelle utilisation, vous devez régler chaque
presseur présent sur le guide.
Vérifier le blocage de chaque vis avant de commencer le
toupillage.
Utilisation des rondelles de table
Les rondelles de table (ou réducteurs de lumière) doivent
être utilisées pour réduire au minimum l’espace entre la
table et la broche.
Avant la mise en marche de la machine, vous devez sys-
tématiquement vérifier de la bonne installation des ré-
ducteurs de lumière (rondelles fournies).
Assurez-vous d’avoir sélectionné le réducteur de lumière
adéquat selon l’outil choisi.
Le réducteur de lumière (rondelles fournies) doit entourer
les fraises le plus complètement possible.
Réglages
Réglage de vitesse de rotation Fig. 19
Le réglage de la vitesse de rotation de la machine com-
porte 6 vitesses (voir caractéristiques techniques)
• Déterminerla vitessederotationoptimaleeneffec-
tuant une découpe de test sur un pièce de déchet.
Attention : Lutilisation de la vitesse de rotation correcte
Installing and changing the clamping sleeves for top spindle
moulders
• Beforechangingtheclampingsleeves,pullthepower
supply plug of your machine. Select the clamping
sleeve matching the diameter of your cutter head.
• Removethereducingpiece fromthe tableopening,
Fig. 16.
• Lockthespindlewiththebuttonatthebottomofthe
spindle, Fig. 18.
• Releasethesafetynutoftheclampingsleeveusing
the key supplied, Fig. 17.
• Inserttheclampingsleeveinthenut,orremoveit.
• Firmlytightenthenutintheclampwhilekeepingthe
spindle locked. Before every use of the machine make
sure that the cutting tool is firmly clamped at the end
of the spindle.
• Set the reducing piece for the opening back to its
original position.
• Adjustthefence,asrequired,bymeansofthescale
on the table.
• Connect thedust extractorunit. It ishighly recom-
mended to connect a dust extractor unit (or system)
in order to keep the opening free from chips, to cool
the motor, and to facilitate the work piece feed.
• Reconnectthemachinetothepowersupply.
Setting the moulding fence
The use of the fence is a must. Every job must be looked
at separately. At every new use you must make sure that
the guards are correctly installed and adjusted.
For every new use, each pressure piece on the fence must
be newly set.
Make sure that all the bolts are firmly tightened before
you start moulding.
Use of the table rings
The table rings (or reduction pieces for the opening) must
be used in order to reduce the spacing between table and
spindle to a minimum.
Before switching on the machine systematically check
the table rings supplied for their correct seat.
Check whether you have chosen the correct ring for the
corresponding cutting tool and its installation height, in
order to reduce the risk of work piece tilting at passing
the opening.
The reduction piece (table ring) must enclose the cutter
head as far as possible.
Adjustments
Adjust the number of revolutions Fig. 19
The speed adjustment of the machine has 6 stages (see
technical data)
• Determinetheoptimalnumberofrevolutionsbyasam-
ple cut in a piece of waste material.
Note: The use of the correct number of revolutions in-
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach SP 52 Spero at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach SP 52 Spero in the language / languages: English, German, Dutch, Danish, French, Swedish as an attachment in your email.

The manual is 7.57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info