782063

Scheppach SP 52 Spero Manual

19
Zoom out
Zoom in
Previous page
1/116
Next page
19
Montage et installation
Mise en garde:
Retirerlachedeprisedecourantavantd’effectuertout
réglage ou entretien.
Fixation de la machine
Pour toute utilisation, il est conseillé de fixer la machine
sur un établi au niveau des 4 trous prévus.
Si la machine est utilisée comme outil portatif, montez-la
surunsupportstabledefaçonàtravaillersansrisque.
La machine a 4 trous au niveau des pieds pour une fixa-
tion ferme.
1 La surface de montage doit être au préalable percée
en tenant compte des espacements des deux trous de
fixation de la base.
2 Chaque pied doit être fermement fixé à l’aide de bou-
lons (non fournis).
3 Les boulons doivent être suffisamment longs: tenir
compte de l’épaisseur du plan de travail sur lequel
est fixée la toupie.
4Utiliserdesrondellesetplacerlesécrousdeserrage
sous le plan de travail.
5 Les dimensions du plan de travail doivent être suffisan-
tes pour éviter le renversement de l’ensemble pendant
le travail.
6 Attention: S’assurer de la stabilité et de la robustesse
du plan de travail avant tous travaux.
Montage du guide de toupillage, Fig. 3
L’assemblage du guide de toupillage:
Le guide de toupillage est livré démonté dans l’embal-
lage. Pour commencer à travailler, vous devez impérative-
ment l’assembler, puis le monter sur la table de travail.
Etape 1: Assemblage des pièces A et B:
Faire coulisser la pièce B sur la pièce A dans la rainure
prévue (cf. Fig. 4). Ensuite insérer la vis à tête ronde et
visser fermement avec la rondelle et la poignée de ser-
rage.
Etape 2: Assemblage des barres de butée C
Insérer deux vis à tête ronde dans les trous de fixation,
visser légèrement avec une rondelle et une vis de serrage,
puis pousser la barre de butée avec la rainure à travers
la tête ronde, et visser les deux fermement avec la vis de
serrage.
Réaliserlemêmeassemblagedel’autrecôtéduguide.
Attention à monter les pièces C dans le bon sens, et à la
même hauteur que la pièce A.
Assembly
Attention
Before doing any setting or maintenance work pull the
power supply plug.
Fixing the machine
When using the machine it is recommended to fasten it
to a work bench by means of the four holes
If the spindle moulder is to be used as a portable ma-
chine fix it to a stable support so your work can be done
without any risk
At the level of the legs the machine has four holes for
safe fastening
1. Holes must be drilled in the assembly surface, consid-
ering the spacing of the two fixing holes in the base.
2. Each leg must be tightened with bolts (not supplied).
3. The bolts must be sufficiently long: Take into account
the thickness of the working surface onto which the
machine has to be fastened.
4.Usethewashersandscrewtheworkingsurfaceonwith
the nuts.
5. The working surface must be sufficiently large in order
to prevent tilting of the unit during working.
6. Attention: Before starting work, check the solidity of
the working surface.
Mounting the moulding fence, Fig. 3
Assembly of the moulding fence:
The moulding fence has been shipped in the carton box
disassembled. Before starting work, it must be assembled
and fitted onto the working table.
Step 1: Assembly of part A and B
Slide part B onto part A in the groove provided (see Fig.
4). Now insert the round-headed bolt and firmly tighten it
with washer and clamping lever.
Step 2: Fitting the stop bars C
Insert the two round-headed bolts into the fastening
holes, screw them slightly in with washer and clamp-
ing screw, slide the stop bar with the groove through the
round head, and tighten both with the clamping screw.
Do the same assembly at the other side of the fence.
Make sure to assemble the parts C in the correct direc-
tion. Make also sure that the parts C are at the same
height as part A.
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach SP 52 Spero at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach SP 52 Spero in the language / languages: English, German, Dutch, Danish, French, Swedish as an attachment in your email.

The manual is 7.57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info