Manual Scheppach SP 2111 Spero (page 18 of 32) (English, German, Dutch)

782273

Zoom out

Zoom in

1/32

Operations

After having performed all the above procedures and

opera tions, you may begin cutting.

ATTENTION: Always keep hands away from the cutting

area and do not try to approach it when the machine is

running.

Switching the product on/off, Fig. 1

To switch the plunge-cut saw on, press the on/off switch

(4). To switch off, release the on/off switch (4).

Operating and holding the plunge-cut saw, Fig. 8

1 Secure the work piece so that it cannot get displaced

or moved while sawing.

2 Only move the saw forwards.

3 Grip the saw tightly with both hands ensuring that one

hand is placed on the main handle and the other on

the front handle.

4 When using a guide rail, it must be fastened with screw

clamps.

5 Make sure the power cable is not placed in the sawing

direction.

Sawing

1 Place the front part of the machine onto the work piece.

2 Switch the machine on using the on/off switch (4).

3 Press the plunge-cut trigger (3).

4 Push the saw downwards to reach the sawing depth.

5 Push the saw forward evenly.

6 After ﬁnishing the sawing cut, switch the machine off

and move the saw blade upwards.

Plunge-cuts, Fig. 9

1 Place the saw onto the work piece.

2 Place the cutting indicator with the rear arrow (A) on

the deepest plunge-cut position.

3 Switch the machine on and push the saw downwards

until you reach the set cutting depth.

4 Move the saw forwards until the cutting indication (C)

has reached the marked point.

5 After completion of the plunge-cut, move the saw blade

upwards and switch the saw off.

Cutting with rails (otional)

1 Place the machine in the guide rails. can be readjusted

using the hex driver included in the delivery, when

there is the risk of the adjusting screws releasing by

themselves.

2 Turn on the machine by pressing the on/off switch (4).

3 Press the dip trigger (3).

4 Press the saw downwards to reach the sawing depth.

During ﬁrst use the rubber lip is sawn off and thus

splitter protection is guaranteed up to the saw blade.

5 Push the saw uniformly forwards.

6 Turn off the machine and tilt the saw blade to the top

when the saw cutting is complete.

Sawing with dust suction

Connect the suction hose to the exhaust nozzle - Ø 38

mm (12).

ELECTRICAL CONNECTIONS

Check that the electrical system to which the machine is

connected is earthed in compliance with current safety

regulations and that the current socket is in perfect con-

dition.

The electrical system must be ﬁtted with a magnetother-

mal protective device to safeguard all conductors from

short circuits and overload.

The selection of this device should be in line with the

following electrical speciﬁcations of the machine stated

on the motor.

NOTE: Your plunge cut saw’s electrical system is equipped

with an undervoltage relay which automatically opens the

circuit when the voltage falls below a minimum pre-est-

ablished limit and which prevents the self-reset of ma-

chine functions when voltage returns to normal levels.

If the machine stops involutarily, do not be allarmed.

Make sure that there has not been a voltage failure in the

electrical system.

ADJUSTING

Caution: Prior to carrying out one of the following adjust-

ment steps, switch the machine off and unplug the mains

plug.

Cutting depth adjustment, Fig. 2

The cutting depth can be adjusted from 0 to 45 mm.

Unfasten the cutting depth adjustment screw (6) and set

the required depth using the scale (7) and retighten the

screw.

The dimentions on the rail shows the cutting depth with-

out rail.

Mitre settings, Fig. 3

The mitre square can be set from 0° to 45°.

Unfasten the mitre adjustment screws (8) on both sides,

set the desired mitre square on the scale (9) and retight-

en both screws.

Saw blade replacement, Fig. 4, 5, 6

Caution: Before you are going to make the saw blade change,

switch off the machine and unplug the power cord.

1 Press the plunge trigger (3), bring the saw blade into

the blade-change position (Adjustment screw for depth

of cut shall be adjusted to 25mm) and insert the hex

wrench into the blade locking screw (17).

2 Press on the shaft lock (13) and rotate the saw blade

(10) until the lock clicks into place.

3 Hold down the locking shaft (13) and open the blade

locking screw (17) counter clockwise, while keeping

the blade in the blade-changing position.

4 Remove the outer ﬂange (16) and the saw blade (10).

(Caution: risk of injuries, wear protective gloves)

5 Insert the new blade and ﬂange.

6 Screw in and tighten the saw blade locking screw while

keeping the shaft locking mechanism pressed again.

7 Set the plunge saw to its original position.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach SP 2111 Spero in the language / languages: English, German, Dutch as an attachment in your email.

The manual is 2.59 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach SP 2111 Spero Manual

Product: