Manual Scheppach SL9LXU Woodster (page 26 of 44) (English, German, French)

782501

Zoom out

Zoom in

1/44

26 GB/IE

8.8 Limiting the cutting depth (Fig. 3/13)

• The cutting depth can be innitely adjusted using the

screw (25). To do this loosen the knurled nut (d) on

the screw (25). Move the stop for the cutting depth

limitre (26) to the outside. Turn the screw (25) in or

out to set the required cutting depth. Then re-tighten

the knurled nut on the screw (25).

• Check the setting by completing a test cut.

8.9 Sawdust bag (Fig. 1)

The saw is equipped with a debris bag (18) for saw-

dust and chips.

Squeeze together the metal ring on the dust bag and

attach it to the outlet opening in the motor area.

The debris bag (18) can be emptied by means of a zip-

per at the bottom.

8.10 Changing the saw blade (Fig. 14-17)

Remove the power plug!

Important.

Wear safety gloves when changing the saw blade.

Risk of injury!

• Swing up the machine head (4).

• Undo the screw (g) on the guide bar (35), so that it can

move freely and be pivoted downwards.

• Loosen the screw (f) of the ange cover so that it is

free to move.

• Press the release lever (2). Swing up the saw blade

guard (5) to the point where the recess in the saw

blade guard (5) is above the ange bolt (29).

• Insert the allen key (e) in the ange bolt (29).

• Firmly press the saw shaft lock (31) and slowly rotate the

ange bolt (29) in clockwise direction. The saw shaft lock

(31) engages after no more than one rotation.

• Now, using a little more force, slacken the ange bolt

(29) in the clockwise direction.

• Turn the ange screw (29) right out and remove the

external ange (30).

• Take the blade (6) off the inner ange (32) and pull

out downwards.

• Carefully clean the ange screw (29), outer ange (30)

and inner ange (32).

• Fit and fasten the new saw blade (6) in reverse order.

• Important! The cutting angle of the teeth, in other

words the direction of rotation of the saw blade (6)

must coincide with the direction of the arrow on the

housing.

• Move the guide bar (35) into position and tighten the

screw (f; g) again.

• Before continuing your work make sure that all safety

devices are in good working condition.

• Important! Every time that you change the saw blade

(6), check to see that it spins freely in the table insert

(10) in both perpendicular and 45° angle settings.

• Important! The work to change and align the saw

blade (6) must be carried out correctly.

8.11 Using the laser (Fig. 18)

• To switch on: Move the ON/OFF switch of the laser

(34) to the “1” position. A laser line is projected onto

the material you wish to process, providing an exact

guide for the cut.

• To switch off: Move the ON/OFF switch of the laser

(34) to the “0” position.

8.12 Adjusting the laser (Fig. 19)

If the laser (33) ceases to indicate the correct cutting line,

you can readjust the laser. To do so, open the screws

(36) and set the laser by moving sideways to that the

laser beam strikes the teeth of the saw blade (6).

9. Transport

• Tighten the set screw (26) in order to lock the rotary

table (14)

• Activate the release lever (3), press the machine

head (4) downwards and secure with the safety pin

(23). The saw is now locked in its bottom position.

• Fix the saw’s drag function with the locking screw for

drag guide (20) in rear position.

• Carry the equipment by the xed saw table (15).

• When reassembling the equipment proceed as de-

scribed under section 7.

10. Maintenance

m Warning! Prior to any adjustment, maintenance or

service work disconnect the mains power plug!

General maintenance measures

Wipe chips and dust off the machine from time to time us-

ing a cloth. In order to extend the service life of the tool, oil

the rotary parts once monthly. Do not oil the motor.

When cleaning the plastic do not use corrosive products.

Brush inspection

Check the carbon brushes after the rst 50 operating

hours with a new machine, or when new brushes have

been tted. After carrying out the rst check, repeat the

check every 10 operating hours.

If the carbon is worn to a length of 6 mm, or if the spring

or contact wire are burned or damaged, it is necessary

to replace both brushes. If the brushes are found to be

usable following removal, it is possible to reinstall them.

11. Storage

Store the device and its accessories in a dark, dry and

frost-proof place that is inaccessible to children. The

optimum storage temperature is between 5 and 30˚C.

Store the electrical tool in its original packaging.

Cover the electrical tool in order to protect it from dust

and moisture.

Store the operating manual with the electrical tool.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach SL9LXU Woodster in the language / languages: English, German, French as an attachment in your email.

The manual is 4.69 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach SL9LXU Woodster Manual

Product: