782365
27
Zoom out
Zoom in
Previous page
1/84
Next page
27
Changing Blades Fig. 6
WARNING: To avoid injury from accidental starting, always
turn the switch off and remove the power plug from the power
source before changing the blades.
• Pullthepowerplug.
• Putthesawingunitintheupperposition.
• Releasehexagonbolt1andremovehexagonbolt2.
• Release the movable saw blade guard 8 by pressing
lock 3.
• Liftthesawbladeguardatthesametimetofreethe
saw blade.
• Release the saw blade xing screw (Attention: left
handedthread).
• Removeboltandsawbladeange.
• Take off the saw blade with caution (risk of injury
throughsawbladeteeth).
• Place the new saw blade onto the inner saw blade
flange, observing the correct size and the turning direc-
tion of the saw blade.
• Puttheoutersawbladeangeinplaceandrmlytight-
en the screw.
• Returnthesawbladeguardtothecorrectpositionand
tighten screws 1 and 2.
Maintenance
WARNING: For your own safety, turn the switch off and remove
the plug from the power source outlet before maintaining or
lubricating your mitre saw.
General Maintenance
Occasionallyuseaclothtowipeoffchipsanddustfrom
themachine.Oiltherotarypartsonceamonthtoextend
the tool life. Do not oil the motor.
Brush Inspection
Checkthemotorbrushesaftertherst50hoursofusefor
a new machine or after a new set of brushes have been
installed. After the rst check, examine them every 10
hours of use.
Whenthecarboniswornto6mminlengthorifthespring
orshuntwireisburnedordamaged,replacebothbrushes.
If the brushes are found serviceable after removing, rein-
stall them.
Remplacement de la lame, Fig. 6
ATTENTION : Pour éviter de se blesser si la scie devait se
mettre en marche accidentellement, débrancher la scie et
retirer la fiche de la prise de courant avant de changer la
lame.
• Débrancherlaprised’alimentation.
• Mettrel'agrégatàlapositionsupérieure.
• Relâcherleboulonàsixpans1etéloignerleboulon
2.
• Ouvrir le protecteur de la lame de scie exible 8 en
appuyantledispositifdeblocage3.
• En faisant cela, relever le protecteur pour libérer la
lame.
• Relâcherlavisdeblocagedelalame(Attention:letà
gauche).
• Enleverleboulonetlaasquedelalame.
• Eloignerlalameaveccaution(risquedeblessurespar
lesdentsdelalame).
• Mettrelanouvellelamesurlaasqueintérieure,enfai-
santattentionàlatailleetladirectionderévolution.
• Mettrelaasqueextérieuresurplaceetlaserrerferme-
ment.
• Remettrele protecteur delalamede scie àsaplace
correcte et resserrer les boulons 1 et 2.
Entretien
ATTENTION : Dans l’intérêt de votre sécurité, mettre la scie
hors tension et retirer la fiche de la prise de courant avant
tout entretien ou toute lubrification de la scie.
Entretien courant
Detempsentemps,essuyerlascieavecunchiffonpour
enretirerlescopeauxetlapoussière.Unefoisparmois,
huilerlespiècesrotativespourprolongerladuréedevie
utiledelascie.Nepashuilerlemoteur.
Inspection des balais
Vérierlesbalaisdumoteuraprèsles50premièresheu-
resdeserviced’unescieneuveouaprèsl’installationd’un
nouveaujeudebalais.Aprèscettepremièrevérication,
lesinspectertoutesles10heuresdeservice.
Quand l’usure des balais a réduit à 6 mm la longueur
ducharbonousileressortouleldedérivationestbrûlé
ouendommagé,remplacerlesdeuxbalais.Si,aprèsles
avoirretirés,onconstatequelesbalaissontenbonétat
deservice,lesremettreenplace.
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach SL10D Woodster at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach SL10D Woodster in the language / languages: English, German, Dutch, Danish, French, Finnish as an attachment in your email.

The manual is 4.69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info