782365
17
Zoom out
Zoom in
Previous page
1/84
Next page
17
Setting the Tool
Note:
Thistoolisaccuratelyadjustedbeforeshippingfromthe
factory. Check the following accuracy and readjust if nec-
essaryinordertoobtainthebestresultsinoperation.
Adjusting the Bevel Stops at 90° and 45° (Fig. 3)
• Loosen the Bevel Lock Handle and move the cutting
headallthewaytotherightandtightentheBevelLock
Handle 1.
• Useasquaretosetthebladeat90°tothetable.
• Ifanadjustmentisnecessary,loosenthelocknut2and
adjustthebolt3usingthesuppliedwrenchsothatthe
blade is 90° to the table.
• Tightenthelocknut.
• Adjustthebevel indicator 4 to the 0 markusingthe
screw.
• Toadjustthe45°stop,followthesameprocedureas
the 90° but move the cutting head to the left and use
the lock nut 2 and bolt 3.
Adjusting the Fence
• Lowerthecuttingheadandpushinthelockpin.Make
surethetableisin0mitreposition.
• Placeacombinationsquareagainstthefenceandnext
to the saw blade.
• If the blade does not contact the square, loosen the
screws .
• Adjustthefencesothatthefencehasfullcontactwith
the square. Tighten the screws.
Connecting to the Power Supply
Checkthatthepowersupplyandoutletusedare inac-
cordance with your mitre saw. Have a look at the rating
plate of the motor or the rating on the mitre saw. Any
changesshouldalwaysbecarriedoutbyaqualiedelec-
trician.
This is a double insulated tool which eliminates the need
foranearthedpowersupplysystem.
WARNING! Avoid contact with the terminals on the plug when
installing (removing) the plug to (from) the power supply out-
let. Contact will cause a severe electrical shock.
Using an Extension Lead
The use of any extension lead will cause some loss of
power.To keep this toaminimumandtopreventover-
heatingandpossiblemotor burnout,askadvicefroma
qualiedelectriciantodeterminetheminimumwiresize
of the extension lead.
Theextensionleadshouldbeequippedwithanearthed
type plug that ts the power supply outlet at one end,
andwithanearthedtypesocketthattstheplugofthis
machine at the other end.
Réglage de la scie
N. B. :
Lascieaétéajustéeavecprécisionenusine avantson
expédition.Pourobtenirlesmeilleursrésultats,faireles
véricationssuivantesdelaprécisionetajusterdenou-
veau au besoin.
Réglage des angles de chanfrein de 90° et 45° (Fig. 3)
• Desserrerlamanettedeblocagedechanfreinetpous-
serlatêtedecoupeversladroiteaussiloinqu’ellepeut
aller,puisresserrerlamanettedeblocage1.
• Al’aided’uneéquerre,ajusterlalamepourlamettre
perpendiculaireauplateau.
• Siunajustements’impose,desserrerlecontreécrou2
etajusterleboulon3àl’aidedelacléfournieàcette
n,defaçonquelalamesoitperpendiculaireaupla-
teau.
• Serrerlecontreécrou.
• Amenerl’indicateurdechanfrein4àlagraduation0en
tournant la vis.
• Pourleréglageà45°,procéderdelamêmefaçon,mais
pousserlatêtede coupe vers la gauche et utiliser le
contreécrou2etleboulon3.
Adjustement du guide
• Abaisserlatêtedecoupeetlabloqueraveclagoupille
desécurité.S’assurerqueleplateauestdanslaposi-
tion d’onglet 0.
• Placerl’undesbrasd’uneéquerrecombinéecontrele
guide et l’autre contre la lame de scie.
• Silalamenetouchepasl’équerre,desserrerlesvis.
• Ajusterleguidedefaçonqu’iltouchel’équerretoutau
long. Serrer les vis.
Branchement de la scie
S’assurerquelecourantetlapriseutiliséecorrespondent
àcedontlascieabesoin.Voirlesspécicationsqui-
gurentsurlaplaquesignalétiquedumoteuroucellesqui
gurentsurla scie. Toutchangement doit être effectué
parunélectricienqualié.
Ayantunedoubleépaisseurd’isolement,lascien’apas
besoin d’une alimentation mise à la terre.
ATTENTION : Eviter tout contact avec les pointes de la fiche
quand on l’enfiche dans la prise de courant ou qu’on l’en re-
tire. Tout contact causera un choc électrique dangereux.
Emploi d’une rallonge
L’emploi d’une rallonge entraîne automatiquement une
certainepertedecourant.Pourminimisercetteperteet
empêcherlemoteurdes’échaufferetdegriller,deman-
deràunélectricienqualiéquelcalibreminimaldella
rallonge doit avoir.
Larallongedoitêtremunie,àuneextrémité,d’uneche
mâleavecmiseàlaterre,quis’enchedanslaprisede
courantet,àl’autreextrémité,d’unechefemelleavec
miseàlaterre,quis’enchedanslascie.
Montage de la scie
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach SL10D Woodster at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach SL10D Woodster in the language / languages: English, German, Dutch, Danish, French, Finnish as an attachment in your email.

The manual is 4.69 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info