782422
89
Zoom out
Zoom in
Previous page
1/180
Next page
89
Impostazione profondità normale Fig. 6.1
La sega funziona 5 mm al di sotto della superficie del
tavolo. (Pezzi separati.)
Blocco profondità (1) adiacente all’alloggiamento.
Vite di arresto (2) in aggiunta.
Vite di regolazione (3) non ha alcuna funzione.
Impostazione profondità variabile Fig. 6.2
La sega funziona al di sopra della superficie del tavolo.
(Tagli coperti)
Impostare blocco profondità (1) all’esterno.
Impostare la vite di regolazione (3) alla misura
desiderata, e assicurare con un contro-dado (4).
Effettuare una prova di taglio.
Vite di arresto (2) non in aggiunta.
Trasporto della macchina
• Allentarelamanopoladiinnestodellosmussoeruotare
il banco completamente verso destra. Bloccare il banco
in un angolo obliquo di 45°.
• Spostare all’indietro la testa di taglio e bloccare il
carrello.
• Abbassarelatestaditaglioepremerel’innestodibloc-
caggio.
• Trasportarelatranciatrice/taglierinatramitel’impugna-
tura integrata e il lato dello zoccolo.
Sostituzione delle lame della sega, Fig. 7
ATTENZIONE: Prima della sostituzione della lama della sega
si deve spegnere l’interruttore e staccare la presa dalla
corrente, per evitare infortuni derivanti dall’accensione ac-
cidentale della macchina.
• Staccarelaspinadallapresadicorrente.
• Posizionarelasegasullaposizione“funzionetronca-
trice”.
• Sbloccarelaprotezioneremovibiledellalama(7)pre-
mendo il blocco 3 (Fig. 1).
• Farscorrerelaprotezionedellalama(7)inmodotale
da poter rimuovere la lama (8).
• PremereilbloccoAdellalama(Fig.7.1)sinoaquando
la lama non va nella sua sede.
• Allentarelevitidissaggiodellalamaconunachiave
a perno in dotazione (B) (Attenzione, girare verso sini-
stra).
• Rimuoverelaviteelaangiadellalama.
• Rimuovereconattenzionelalama.Attenzione:Pericolo
di infortunio dovuto alla lama.
• Posizionarelanuovalamaall’internodellaangiadella
lama, osservare la grandezza corretta e la direzione di
rotazione della lama.
• Riposizionarelaangiaesternadellalamaestringere
bene la vite.
• Posizionarela protezionedella lamanellaposizione
corretta.
Ajuste normal de profundidad Fig. 6.1
Función de sierra 5 mm por debajo de la tabla de la mesa.
(separar las piezas de trabajo)
Tope de profundidad (1) adjuntado a la carcasa
Tornillo de tope (2) viene inserto.
Tornillo de regulación (3) no tiene ninguna función.
Ajuste regulable de profundidad Fig.6.2
Función de la sierra sobre la tabla de la mesa. (cortes
ocultos)
Ajustar el tope de profundidad (1) hacia afuera.
Regular el tornillo de ajuste (3) a la medida deseada
Regular la medida y asegurar con la contratuerca (4).
Realizar un corte de prueba.
El tornillo de tope (2) no está en uso.
Transporte de la máquina
• Sueltelaprotecciónparacubrirlaingletadoraymueva
la mesa hacia la derecha del todo.
• Muevalacabezadecortehaciaarribaydespuéscierre
el carro.
• Pongaelcabezalcortantehaciadelanteycierreade-
cuadamente el carrito.
• Bajeelcabezalcortanteypresioneelbotóndeencaje
de la ingletadora.
• Cojaestasierraingletadoraconcubiertaporelasaque
lleva incorporada y por el zócalo.
Cambiar la hoja de la sierra (Fig. 7)
ADVERTENCIA: antes del reemplazo de las hojas de sierra,
deberá apagar el interruptor y desconectar el enchufe de la
toma a fin de no sufrir lesión alguna debida a un arranque
involuntario de la máquina.
• Desconectarelenchufe.
• Colocarlaunidaddesierraenposición“modomitra”.
• Desbloquearlaprotecciónmóvildelahojadesierra
(7) presionando la traba 3 (Fig. 1).
• Levantealavezlaproteccióndelahojadesierra(7)
para liberar la hoja de sierra (8).
• Presionarla trabaA delahoja desierra (Fig.7.1),
hasta que la hoja de sierra calce en el sitio.
• Aojeeltornillodesujecióndelahojadesierraconla
llave de tubo provista (B) (Atención, rosca izquierda).
• Retirareltornilloylabridadelahojadesierra.
• Retirarlahojadesierraconsumocuidado.Atención:
peligro de lesión por la hoja de sierra.
• Colocarlanuevahojadesierraenlabridainternadela
hoja de sierra, observando al mismo tiempo el tamaño
y la dirección de giro correcta de la hoja de sierra.
• Colocarlabridaexternadelahojadesierrayasegurar
fuertemente el tornillo.
• Volveracolocarlaproteccióndelahojadesierraen
su posición correcta.
BA sl 8-10 lxu.indd 89 28.02.11 11:01
89


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach SL 1 0 LXU Woodster at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach SL 1 0 LXU Woodster in the language / languages: English, German, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5.1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info