782422
29
Zoom out
Zoom in
Previous page
1/180
Next page
29
Replacing the laser’s batteries (fig. 8)
• Removethelaserbatterycompartmentcover1.Remove
both batteries.
• Replacebothbatterieswiththesameoranequivalent
type. Make sure that the poles face in the same direc-
tion as the old batteries.
• Closethebatterycompartmentcover.
• Checkthelaserline.Readjustifnecessary.
Maintenance
WARNING: For your own safety, turn the switch off and re-
move the plug from the power source outlet before maintain-
ing or lubricating your mitre saw.
General Maintenance
Occasionally use a cloth to wipe off chips and dust from
the machine. Oil the rotary parts once a month to extend
the tool life. Do not oil the motor.
Brush Inspection
Check the motor brushes after the first 50 hours of use
for a new machine or after a new set of brushes have
been installed. After the first check, examine them every
10 hours of use.
When the carbon is worn to 6 mm in length or if the
spring or shunt wire is burned or damaged, replace both
brushes. If the brushes are found serviceable after remov-
ing, reinstall them.
m Electrical connection
The installed electric motor is completely wired ready for
operation.
The customer’s connection to the power supply system, and
any extension cables that may be used, must conform with
local regulations.
Important remark:
The motor is automatically switched off in the event of
an overload. The motor can be switched on again after a
cool ing down period that can vary.
Defective electrical connection cables
Electrical connection cables often suffer insulation dam-
age.
Possible causes are:
• Pinchpointswhenconnectioncablesarerunthrough
window or door gaps.
• Kinksresultingfromincorrectattachmentorlayingof
the connection cable.
Remplacement des piles du laser (Fig. 8)
• Enleverlecouvercleducompartimentdepilesdulaser
1. Enlever les 2 piles.
• Remplacerlesdeuxbatteriespardesbatteriesneuves
identiques ou d’un type équivalent. Veiller à insérer
les piles en respectant la polarité, dans le même
sens que les piles usées.
• Fermerlecouvercleducompartimentdepiles.
• Vérierlalignelaser.Encasdebesoin,refairele-
glage.
Entretien
ATTENTION: Dans l’intérêt de votre sécurité, mettre la scie
hors tension et retirer la fiche de la prise de courant avant
tout entretien ou toute lubrification de la scie.
Entretien courant
De temps en temps, essuyer la scie avec un chiffon pour
enretirerlescopeauxetlapoussière.Unefoisparmois,
huiler les pièces rotatives pour prolonger la durée de vie
utile de la scie. Ne pas huiler le moteur.
Inspection des balais
Vérifier les balais du moteur après les 50 premières heu-
res de service d’une scie neuve ou après l’installation
d’un nouveau jeu de balais. Après cette première vé-
rification, les inspecter toutes les 10 heures de service.
Quandl’usuredesbalaisaréduità6mmlalongueur
ducharbon ou si le ressort ou le fil de dérivation est brûlé
ou endommagé, remplacer les deux balais. Si, après les
avoir retirés, on constate que les balais sont en bon état
de service, les remettre en place.
m Raccordement électrique
Le moteur électrique qui est installé est raccordé en ordre
de marche.
Le raccordement électrique que doit effectuer le client ainsi
que les cables de rallonge utilisés doivent correspondre aux
normes en vigueur.
Remarques importantes
En cas de surcharge du moteur, celui-ci s’arrête auto-
matiquement. Après un temps de refroidissement (d’une
durée variable), il est possible de remettre le moteur en
marche.
Câbles de branchement électrique défectueux
Il arrive fréquemment que l’isolation des câbles de bran-
chement électrique présente des avaries.
Les causes en sont:
• Écrasements, si le câble passe sous la porte ou la
fenêtre.
• Coudes dûsàune mauvaisexation ouun mauvais
guidage du câble de branchement.
BA sl 8-10 lxu.indd 29 28.02.11 11:01
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach SL 1 0 LXU Woodster at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach SL 1 0 LXU Woodster in the language / languages: English, German, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5.1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info