782422
25
Zoom out
Zoom in
Previous page
1/180
Next page
25
Crown Moulding Cut
• Crownmouldingcanonlybecutatonthetableusing
this mitre saw.
• Thismitresawhasspecialmitrestopsof31.6°left
and right and a bevel stop of 33.9° for a special crown
moulding 1 i.e. 52° between the back of the moulding
and the top flat surface that fits against the ceiling; 38°
between the back of the moulding and the bottom flat
surface that fits against the wall. Refer to the following
table for this crown moulding cut.
Settings Left side Right side
Inside corner Mitre angle 30° right 30° left
Bevel angle 33,9° 33,9°
Moulding
position
Top against
fence
Bottom against
fence
Finished side Keepleftside
of cut
Keepleftside
of cut
Outside corner Mitre angle 30° left 30° left
Bevel angle 33,9° 33,9°
Moulding
position
Bottom against
fence
Top against
fence
Finished side Keeprightside
of cut
Keeprightside
of cut
Note:
• Thesespecialstopscannotbeusedwith45°crown
moulding.
• Sincemostroomsdonothaveanglesofexactly90°,
fine tuning is needed and always take a test cut to
confirm the correct angles.
Pullover Cut
WARNING:
1. Never pull the cutting head assembly and spinning blade
towards you during the cut. The blade may try to climb up on
the top of the workpiece, causing the cutting head assembly
and spinning blade to kick back.
2. Never lower the spinning saw blade down before pulling
the cutting head to the front of the saw.
• Unlockthecarriage1withthelockhandle2andallow
the cutting head assembly to move freely. (Fig. 6)
• Movethemitrehandleandcuttingheadtothedesired
mitre angle and bevel angle according to the mitre cut
and bevel cut procedures.
• Graspthe sawhandle andpull thecarriage forward
until the centre of the saw blade is over the front of
the work piece.
• Activatetheswitch,thenpressthebladeguardlock
lever to lower the cutting head down.
• Whenthesawreachesfullspeed,pushthesawhandle
down slowly, cutting through the leading edge of the
workpiece.
• Slowlymovethesawhandletowardthefence,complet-
ing the cut.
• Releasetheswitchandallowthebladetostopspinning
before allowing the cutting head to raise.
Coupe de moulures de plafond
• Lesmouluresdeplafondnepeuventêtrecoupéesqu’à
plat sur le plateau avec cette scie.
• Cette scie a des butées d’onglet spéciales à 30° à
gauche et à droite et une butée de chanfrein à 33,9°
pour une moulure spéciale de plafond 1, c’est-à-dire
à 52° entre le dos de la moulure et la surface plate
supérieure qui s’attache au plafond, et à 38° entre le
dos de la moulure et la surface plate inférieure qui
s’attache au mur. Voir le tableau suivant pour la coupe
des moulures de plafond.
Réglages Coté gauche Coté droite
Coin intérieur Angle d’onglet 30° à droite 30° à gauche
Angle de
chanfrein
33,9° 33,9°
Position de la
moulure
Dessus contre le
guide
Dessous contre
le guide
Coté fini Scier à gauche
du trait
Scier à gauche
du trait
Coin extérieur Angle d’onglet 30° left 30° left
Angle de
chanfrein
33,9° 33,9°
Position de la
moulure
Dessous contre
le guide
Dessus contre le
guide
Coté fini Scier à droite
du trait
Scier à droite
du trait
N. B.:
•Cesbutéesspécialesnepeuventêtreutiliséesqu’avec
une moulure de plafond de 45°.
•Commelescoinsdelaplupartdespiècesnefontpas
un angle exact de 90°, un certain ajustement est né-
cessaire. Toujours faire une coupe d’essai pour vérifier
les angles.
Coupe radiale
ATTENTION:
1. Ne jamais tirer vers soi la tête de coupe avec sa lame
en rotation pendant la coupe. La lame risque de chercher à
grimper sur la pièce à couper, provoquant le rebond de la
tête de coupe et de la lame.
2. Ne jamais abaisser la lame en mouvement avant d’avoir
tiré la tête de coupe vers l’avant de la scie.
• Débloquerlechariot1àl’aidedelamanettedeblo-
cage 2, pour que la tête de coupe puisse se déplacer
facilement (Fig. 6).
• Mettrelamanetted’ongletetlatêtedecoupeàl’angle
d’onglet et à l’angle de chanfrein voulus (voir le mode
d’emploi pour les coupes d’onglet et de chanfrein).
• Saisirlapoignéedelascieettirerlechariotversl’avant
jusqu’à ce que le centre de la lame soit au-dessus de
la partie avant de la pièce à couper.
• Mettrelascieenmarchepuisabaisserlelevierdeblo-
cage du protège-lame pour abaisser la tête de coupe.
• Quandlascieatteintsonpleinrégime,appuyerlen-
tement sur la poignée de la scie pour commencer à
couper le bord d’attaque de la pièce.
• Déplacerlentementlapoignéedelascieversleguide
pour terminer la coupe.
• Relâcherlagachetteetattendrequelalameaitnide
tourner avant de relever la tête de coupe.
BA sl 8-10 lxu.indd 25 28.02.11 11:01
25


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach SL 1 0 LXU Woodster at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach SL 1 0 LXU Woodster in the language / languages: English, German, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5.1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info