782422
23
Zoom out
Zoom in
Previous page
1/180
Next page
23
Mitre Cut
• Makesuretheextensionfenceissecuredinthecorrect
position.
• Releasethemitrelockingbuttonandmovethetableto
the desired angle. Every five degrees, angles from 0° to
45° can be fast and precisely set. Let the mitre button
snap in and fix the angle with the clamping screw.
• Activatetheswitch,thenpressthebladeguardlock
lever to lower the cutting head down.
Bevel Cut
• Loosenthe bevellock handleand movethe cutting
head to the desired angle. Tighten the bevel lock han-
dle.
• Activatetheswitch,thenpressthebladeguardlock
lever to lower the cutting head down.
Compound Cut
• A compoundcut isa combination ofmitre cutand
bevel cut. Refer to the above procedures to perform
this cut.
Base Moulding
• Basemouldingcanbecutverticallyagainstfenceorat
on the table. Follow the table below for reference.
Settings Vertical position
(Back of moulding is
flat against the fence)
Horizontal position
(Back of moulding is
flat on the table)
Extension fence Close to the blade Far from the blade
Bevel angle 45°
Moulding position Left side Right side Left side Right side
Inside
corner
Left
Right
Left
Right
Mitre
angle
Left at
45°
Right at
45°
Moulding
position
Bottom
against
table
Bottom
against
table
Top
against
fence
Bottom
against
fence
Finished
side
Keepleft
side of
cut
Keepright
side of
cut
Keepleft
side of
cut
Keepleft
side of
cut
Outside
corner
Left
Right
Left
Right
Mitre
angle
Right at
45°
Left at
45°
Moulding
position
Bottom
against
table
Bottom
against
table
Bottom
against
fence
Top
against
fence
Finished
side
Keepleft
side of
cut
Keepright
side of
cut
Keepright
side of
cut
Keepright
side of
cut
Coupe d’onglet
• S’assurerqueleguide-rallongeestassujettidansla
bonne position.
• Relâcherleboutondeserrageàongletsettournerla
table à l’angle désiré. Par le trame à chaque 5 degrés,
tous les angles de 0° à 45° peuvent être réglés rapide-
ment et à haute précision. Laisser bloquer le bouton de
serrage et fixer l’angle à l’aide de la vis de blocage.
• Mettrelascieenmarche,puisappuyersurlelevier
du protège-lame supérieur pour abaisser la tête de
coupe.
Coupe en biseau
• Tournerleguide-rallongedansl’autresensetl’installer
en position éloignée de la lame.
• Desserrerlamanettedeblocageetinclinerlatêtede
coupe à l’angle voulu. Serrer la manette de blocage.
• Mettrelascieenmarche,puisappuyersurlelevier
du protège-lame supérieur pour abaisser la tête de
coupe.
Coupe combinée
• Unecoupecombinéecomprendunecoupeàongletet
une coupe en biseau. Pour l’exécuter, voir les instruc-
tions ci-dessus.
Plinthes
• Onpeut couperles plinthesverticalement contrele
guide ou à plat sur le plateau. Voir le tableau ci-des-
sous.
Réglages Position verticale (dos
de la moulure à plat
contre le guide)
Position horizontale
(dos de la moulure à
plat sur le plateau)
Guide-rallonge Près de la lame Loin de la lame
Angle de chanfrein 45°
Position de la moulure Coté
gauche
Coté
droite
Coté
gauche
Coté
droite
Coin
intérieur
Gauche
Droite
Gauche
Droite
Angle 45° à
gauche
45° à
droite
Position
de la
moulure
Dessous
contre le
plateau
Dessous
contre le
plateau
Top
against
fence
Bottom
against
fence
Cote fini Scier à
gauche du
trait
Scier à
droite du
trait
Scier à
gauche du
trait
Scier à
gauche du
trait
Coin
extérieur
Gauche
Droite
Gauche
Droite
Angle 45° à
droite
45° à
gauche
Position
de la
moulure
Dessous
contre le
plateau
Dessous
contre le
plateau
Dessous
contre le
guide
Dessus
contre le
guide
Cote fini Scier à
gauche du
trait
Scier à
droite du
trait
Scier à
droite du
trait
Scier à
droite du
trait
BA sl 8-10 lxu.indd 23 28.02.11 11:01
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach SL 1 0 LXU Woodster at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach SL 1 0 LXU Woodster in the language / languages: English, German, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5.1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info