782189

Scheppach SD1600F Manual

17
Zoom out
Zoom in
Previous page
1/120
Next page
17
de déchet pour quelques sciages d‘essai; réajustez la
position de la table si nécessaire.
Remarque:la table ne doit pas être appuvêele bloc du mo-
teur. Ceci risque de provoquer des bruits indêsirables.
Table de sciage horizontale et déoupages de blais, Fig. 2+3
• La table de sciage peut être inclinée à 45° à gauche
ou laisseé en position horizontale.
• Vous trouverez sous la table de travail l‘échelle
d‘angles pour lire I‘angle d‘inclinaison approximatif.
Pour un réglage plus précis, utilisez du bois de dechet
pour quelques sciages d‘essai; réajustez la position de
la table si nécessaire.
Montage du protecteur de lame, Fig. 4
Avec prudence, montez le protecteur de lame sur la scie,
comme I‘indique I‘illustration. Fixez súrement la vis avec
un écrou et une rondelle.
• Soulevez la scie par le cadre et le socle et poussez-Ia
sur la table d‘ouvrage.
• Familiarisez vous avec les èlèments d‘utilisation et les
caractèristiques de puissance de la scie.
Montage de la scie sur un établi, Fig. 5
• Un établi en bois massif est plus adapté à I‘installation
de Ja scie qu‘un tréteau à panneau dur, oú la vibration
et le bruit sont dérangeants.
• Les outils et le petit matériel de montage nécessaires
pour le montage sur un établi ne sont pas livrés avec
la scie. Utilisez cependant un équipement qui a au
moins la taille suivante :
1 Corps de la scie
2 Support en caoutchouc mousse
3 Table d‘ouvrage
4 Garniture plate
5 Rondelle
6 Ecrou à six aretes
7 Contre-écrou
8 Vis à six arêtes
Quantité Description
4 Vis à six aretes (6 mm) 1/4-20 x longueur
4 Rondelles (7 mm) 9/32 I.D.
8 Ecrous à 6 aretes (6 mm) 1/4-20
5/16“ (8 mm) Dia.
4 Rondelle (7 mm) 9/32 I.D.
Commencez par percer les traus dans la surface partante
et mettez ensuite les vis.
• II n‘est pas non plus livré avec la scie de support en
caoutchouc mousse. Mais nous recommandons forte-
ment I‘utilisation d‘un tel support pour maintenir un
cause undesireable noise.
Horizontal saw bench and diagonal cuts, Fig. 2+3
• The saw bench can be positioned into a 450 diagonal
position or be left in the horizontal position.
• You can read off the approximate slope angle by using
the angle scale located under the work bench. For
more exact adjustment, use scrap wood for some saw
tests; adjust the bench if necessary.
Blade guard assembly, Fig. 4
Install the blade guard to the holder as shown in the
diagram. Secure the screws with a nut and washer.
• Lift the saw onto the frame and base and push it onto
the workbench.
• Familiarize yourself with the saw operating elements
and features.
Mounting the saw on a work bench, Fig. 5
• A workbench made from solid wood is betier than one
made of plywood, as interfering vibrations and noise
are more noticeable with plywood.
• The necessary tools and small parts for assembling
the saw on a workbench are not supplied with the saw.
However, use equipment of at least the following size:
1 Saw body
2 Foam rubber base
3 Work bench
4 Flat seal
5 Washer
6 Hexagonal nut
7 Lock nut
8 Hexagonal bolt
Ouantity Description
4 Hexagonal bolts (6mm) 1/4-20 x length
4 Flat seal (7mm) 9/321.0
4 Washers (7mm) 9/321.0.
8 Hexagonal nuts (6 mm) 1/4-20
First of all, drill holes into the seating surface and then
insert the screws.
• A foam rubber base for reduction of noise is not
supplied with the saw either. However, we expressly
recommend that you use such a base to keep vibration
and noise to a minimum. Ideal size 400 x 240 mm.
… 17 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach SD1600F at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach SD1600F in the language / languages: English, German, Dutch, French, Italian, Polish as an attachment in your email.

The manual is 2.55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info