782077
23
Zoom out
Zoom in
Previous page
1/120
Next page
23
Cutter block guard (Fig. 10.1/10.2)
Height adjustment is done with the star grip J screw fitted
to the left side of the machine. After releasing the star
grip screw K, the cutter block guard can be moved to the
side and the correct planing width set. Press the guard
down again to fix it in the right position, and tighten the
handles.
Surfacing:
The amount of chip removal is set by means L of the scale
M on the front side of the table top M. The best surface is
obtained at a planing depth between 0.5 and 1.5 mm.
Warning:
The part of the cutter block not used must by covered
by the guard. Working position is in front of the machine
at the side of the infeed table. Put the fingers of both
hands on top of the work piece. Do not hold the work
piece edges.
The work pieces to be planed must lie firmly on the table
so they can be guided safely. For short work pieces use a
feed stick.
Thicknessing:
• FollowingthescaleandusingthehandleO on the spin-
dle, set the thicknessing table to the desired height. 1
rotation = 3 mm.
• Narrowwoodisintroducedinthecentre.
• Whenthicknessing,thetablemustbetreatedwithoil
at regular intervals. After a long period of use, or when
planing humid wood, it can happen that the work piece
is not further pulled in.
Warning:
In case of a defect, switch off the machine at once. Do
not remove any chips or splinters from the tables while
the machine is running. Work pieces below 250 mm may
not be planed.
Changing the knives (Fig. 11)
• PutthemainswitchofthemachinetoOFFposition.
• Pullthepowersupplyplugfromthesocket.
• Blockthecutterblockguardintheliftedposition.
• Releaseandremovethefourknifeclampingscrews.
• Lifttheknivesandknifesupportfromthecutterblock.
• Removethechipsandanyresinfromthecutterblock
and knife support.
• Placenewknivesintothecutterblockandxthemwith
the rectangle slots in both screw heads. (With these two
screws, height-adjustment of the knife is done.)
• Placetheknifesupportontotheknife.
• Slightlytightenthefourclampingbolts.
• Repeattheseactionsforthesecondknife.
• Thenadjusttheplaner/thicknesserknivesexactlywith
the output table. Use a ruler that you put onto the out-
put table.
• By the two set screws, the knife can be adjusted for
height.
• Byturningthecutterblockandusingtheruler,youcan
see the height adjustment.
• Theknifeisexactlyset,whentherulerismovedbythe
knives not higher than 3 mm.
• After a successful knife setting, all clamping screws
Protection de l’arbre de rabotage (Fig. 10.1/10.2)
Le réglage en hauteur s’effectue par la vis poignée-étoile
J monté à gauche de la machine. En relâchant cette vis K,
le protecteur des couteaux peut être pousà côté, pour
régler la largeur de rabotage correcte. Presser le protec-
teur à nouveau vers le bas pour le xer dans la position
correcte, et serrer les poignées.
Dégauchisser:
La profondeur de rabotage est réglée par la poignée L
monté sur la face de la table N, à l’aide d’une échelle.
La meilleure M surface s’obtient avec une profondeur de
rabotage entre 0,5 et 1,5 mm.
Attention:
Le dispositif de protection de l’arbre de rabotage doit
recouvrir la partie non utilisée de l’arbre. La position
de travaille est devant la machine à côté d’alimen-
tation de bois. Mettre les doigts de deux mains sur la
pièce à travailler. Ne pas toucher les arêtes du bois.
Seulement traiter des pièces de bois reposant fermément
sur la table et pouvant être guidées de manière sûre. Pour
le dégauchissage de pièces courtes, utiliser un guide
d’avance pour pièce courte.
Raboter:
• Réglerlatablederabotageàlahauteurdésiréeàl’aide
de la poignée O sur la broche, et l’échelle. 1 révolution
= 3 mm.
• Introduiserlespiècesdeboisétroitesaucentre.
• Lorsdurabotage,latabledoitêtrehuiléerégulièrement.
Après une période d’usage prolongée, ou en traitant le
bois humide, l’avance du bois peut être bloquée.
Avertissement:
En cas d’une panne, mettre la machine hors service im-
médiatement. Ne pas enlever des copeaux pendant que
la machine est en marche. Il est interdit de raboter des
pièces de bois d’une dimension inférieure à 25 cm.
Remplacement des fers de rabot (Fig. 11)
• Mettrel'interrupteuràlaposition«Arrêt».
• Débrancherlaprised’alimentation.
• Bloquerlaprotectiondel'arbrederabotagedanssapo-
sition la plus haute.
• Relâcheretenleverles4visdeserragedelame.
• Enleverlalameetlesupportdel'arbre.
• Enlevercopeauxetrésinedel’arbreetdusupport.
• Mettrelanouvellelamedansl'arbreetlaxerparles
fentes dans les 2 têtes de vis. (Ces 2 vis servent à régler
en hauteur la lame.)
• Mettrelesupportdelamesurlalame.
• Serrerlégèrementles4visdeserrage.
• Répéterlaprocédurepourladeuxièmelame.
• Ensuite,réglerprécisementlahauteurdeslamesenre-
lation à la table d’enlèvement, en utilisant une règle.
• La hauteur des lames est gléespar les deux visde
glage.
• Vérierlahauteurdeslamesentournantl’arbre,touten
maintenant la règle sur place.
• Lalamealapositioncorrectesilarègleestavancéepar
les lames pas plus de 3 mm.
• Ensuite,reserrertouteslesvisfermément(8,4N/m).
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach PT 65 Woodster at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach PT 65 Woodster in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 4.44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info