781489
71
Zoom out
Zoom in
Previous page
1/80
Next page
Störungsabhilfe
Störung Mögliche Ursache Abhilfe
1. Sägeblatt löst sich nach
abschalten des Motor
Befestigungsmutter zu leicht angezogen Befestigungsmutter anziehen,
M 20 Linksgewinde
2. Motor läuft nicht an a) Ausfall Netzsicherung
b) Verlängerungsleitung defekt
c) Anschlüsse an Motor oder Schalter
nicht in Ordnung, Bremse lüftet nicht
d) Motor oder Schalter defekt
a) Netzsicherung überprüfen
b) Siehe Bedienungsanweisung Elektrischer
Anschluß Seite 15
c) Von Elektrofachkraft prüfen lassen
d) Siehe Bedienungsanweisung Elektrischer
Anschluß Seite 15
3. Falsche Motordrehrichtung a) Kondensator defekt
b) Falschanschluß
a) Von Elektrofachkraft austauschen lassen
b) Von Elektrofachkraft Polarität Wandsteckdose
tauschen lassen. Phasenwender Phase wenden
4. Motor bringt keine Leistung,
schaltet selbsttätig ab.
a) Überlastung durch stumpfes
Sägeblatt
b) Thermoschutz spricht an
a) geschärftes Sägeblatt einsetzen
b) nach Abkühlzeit wieder einschaltbereit
5. Brandstellen an der Schnittfläche
beim Querschnitt
a) stumpfes Sägeblatt
b) falsches Sägeblatt
c) Längsanschlag nicht parallel zum Sägeblatt
d) Schiebeschlitten nicht parallel zum
Sägeblatt
a) geschärftes Sägeblatt einsetzen
b) Sägeblatt für Längsschnitte einsetzen
c) Längsanschlag austauschen
d) Schiebeschlitten zum Sägeblatt einrichten
6. Nachlassende Sägeleistung bei
voller Motordrehzahl
Riemen gelockert Riemen spannen, siehe Wartung
7. Werkstück klemmt zwischen
Sägeblatt und Längsanschlag
Längsanschlag verläuft nicht paralles zum
Säbeblatt
Längsanschlag-Einstellung überprüfen
Beim Entsorgen der Maschine müssen die örtlichen gesetzlichen Bestimmungen eingehalten werden!
Malfunction Remedies
Malfunction Mögliche Ursache Remedy
1. Saw blade loosens itself after the
motor has switched on
fastening nut not tightened enough tighten fastening nut, M 20 left thread.
2. Motor doesn‘t start a) power breakdown
b) extension cord defekt
c) connections to motor or switch not correct,
brake doesn‘t ventilate
d) motor or switch defect
a) check power fuse
b) See operating instructions for electrical
contacts, pages 28
c) take it to your electrician for examination
d) See operating instructions for electrical
contacts, pages 28
3. Motor advances or retreats a) condensor defect
b) incorrectly connected
a) have your electrician exchange it
b) have an electrician change the polarity of the
electrical outlet
4. Motor has no power, shuts itself off a) overloading through a dull saw blade
b) thermo protection responds
a) insert a sharpened saw blade.
b) ready to turn on again after cool-down time has
been met
5. Burns on the cutting surface
length cuts
diagonal cuts
a) dull saw blade
b) wrong saw blade
c) length stop not parallel to saw blade
d) slide carriage not parallel to saw blade
a) insert a sharpened saw blade
b) insert a saw blade for length cuts
c) exchange length stop
d) adjust slide carriage to the saw blade
6. Cutting power drops at full motor
speed
belt loose tighten belt, See Maintenance
7. Workpiece jams between saw blade
and longitudinal fence
Longitudinal fence not running parallel to saw
blade
Check longitudinal fence setting and readjust
71


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach PRECISA 6.0 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach PRECISA 6.0 in the language / languages: English, German, Dutch, French, Finnish as an attachment in your email.

The manual is 7.7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info