Manual Scheppach Plana 4.1C (page 22 of 88) (English, German, Dutch, French, Finnish)

782090

Zoom out

Zoom in

1/88

After the rst 5 operating hours, oil the plain

bearings of the feed rollers, the adjustment

spindle of the thicknessing table, their bear-

ings. Repeat every 20 operating hours with

further use.

Planing knives

The HSS planing knives inserted in the factory

are operational and set up correctly.

Only well-sharpened and correctly set-up

planing knives guarantee safe work.

We recommend: Always keep a second set of

new planing knives ready for replacement.

Replacement planing knives are available

from your stockist.

Inserting planing knives g. 16

1. Setting screw

2. Pressure screw

3. Planing knives

4. V-ledge

When inserting, be aware that

• there is a risk of injury to ngers and hands.

• the clamping areas in the cutter and the v-

ledges are cleaned.

• the sharpened planing knives are oiled.

• only knives re-sharpened in sets are used.

• inserting the planing knives and v-ledges is

carried out according to the gure.

• the planing knives, knife supports and v-

ledges are ush with the cutter on both

sides.

• the clamping screws are tightened (8.9 N/m).

Warning!

The details concerning knife attachment, knife

protrusion, knife width, min. clamping length

and ideal tightening torque of the knife mount-

ing screws have to be complied with exactly.

Setting up the planing knives g. 16a, b, c

• The HSS planing knives are inserted in the

factory and set up correctly.

If required, you can re-do the settings or rene

them as described.

• Adjust one planing knife after the other.

• Set the position of the planing knife using

the setting screws alternatively until the

blade of the knife touches both perfectly

trimmed boards (used as adjustment gauge)

which are placed on the unloading table.

• Set the loading table to a dressing height of

2 mm.

• Rotate the cutterblock until the knife has

reached the maximum height.

• The planing knives are positioned on the

head of the setting screws in the slot of the

cutterblock. Let the knives touch the boards

by unscrewing the setting screws with an Al-

len key.

• Align the knife support and check the posi-

tion of the knives again.

• Checking the knives

Put a trimmed board (adjustment gauge) on

the unloading table and mark the position of

the board.

By turning the cutterblock in the cutting direc-

tion by hand, the knife blade should move the

board by x = 2 to 3 mm. Carry out this check

for every knife on the operating side and on

the other side.

Without careful settings, the trimming cannot

be exact.

• Tighten the pressure screws on the v-ledge

with a at spanner (8.9 N/m).

• Adjust all planing knives in the same way

and clamp them.

• Carry out a test-run after every knife re-

placement and tighten the pressure screws

afterwards (8.9 N/m).

Before using the cutterblock, check if the in-

structions above were followed.

Before turning on the machine, the general

safety notices must be observed.

Sharpening of planing knives

Blunt planing knives increase the risk of acci-

dents and the performance is no longer guar-

anteed.

Re-sharpen the planing knives only up to a

knife height of 16 mm. The cutting angle of the

knife should be 40 ± 2 degrees.

For re-sharpening, take the planing knives to

an authorised sharpening company or send

them back to the manufacturer.

Scheppach Fabrikation von Holzbearbeitungs-

maschinen GmbH

Günzburger Straße 69

0-89335 Ichenhausen / BRD

Planing knives:

Plana 3.1c

Set of HS-planing knives 250: 790 2200 601

Set of reversible knives 250: 330 4200 030

Set of knife supports 250: 330 4300 038

Plana 4.1c

Set of HS-planing knives 310: 330 4000 010

Set of HS-planing knives 310: 730 2200 603

Set of reversible knives 310: 330 4200 031

Set of knife supports 310: 790 2200 602

Plana 6.1c

Set of HS-planing knives 410: 790 2200 604

Service information

Please note that the following parts of this

product are subject to normal or natural wear

and that the following parts are therefore also

required for use as consumables.

Wear parts:* motor drive belt, carbon brushes,

planer blades

* Not necessarily included in the scope of de-

livery!

Disposal and recycling

The equipment is supplied in packaging to pre-

vent it from being damaged in transit. The raw

materials in this packaging can be reused or

recycled. Never place batteries in your house-

hold refuse, in re or in water. Batteries should

be collected, recycled or disposed of by envi-

ronment-friendly means. The equipment and

its accessories are made of various types of

material, such as metal and plastic. Defective

components must be disposed of as special

waste. Ask your dealer or your local council!

Old devices must not be disposed of with

household waste!

This symbol indicates that this product

must not be disposed of together with

domestic waste in compliance with the

Directive (2012/19/EU) pertaining to

waste electrical and electronic equipment

(WEEE). This product must be disposed of at a

designated collection point. This can occur, for

example, by handing it in at an authorised col-

lecting point for the recycling of waste electri-

cal and electronic equipment. Improper han-

dling of waste equipment may have negative

consequences for the environment and human

health due to potentially hazardous substanc-

es that are often contained in electrical and

electronic equipment. By properly disposing of

this product, you are also contributing to the

effective use of natural resources. You can ob-

tain information on collection points for waste

equipment from your municipal administration,

public waste disposal authority, an authorised

body for the disposal of waste electrical and

electronic equipment or your waste disposal

company.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach Plana 4.1C in the language / languages: English, German, Dutch, French, Finnish as an attachment in your email.

The manual is 7.95 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach Plana 4.1C Manual

Product: