Manual Scheppach Plana 4.1C (page 19 of 88) (English, German, Dutch, French, Finnish)

782090

Zoom out

Zoom in

1/88

Warning! This electric tool generates an elec-

tromagnetic eld during operation. This eld

can impair active or passive medical implants

under certain conditions. In order to prevent

the risk of serious or deadly injuries, we rec-

ommend that persons with medical implants

consult with their physician and the manufac-

turer of the medical implant prior to operating

the electric tool.

Intended use m

• The planer has been constructed exclusive-

ly for processing wood using the tools and

accessories on offer. No metal workpieces

my be machined.

• The machine complies with the relevant EC

machine guidelines.

• The machine has been designed for single-

shift operation, duty-cycle S1.

• •All safety and hazard notices on the ma-

chine must be observed.

• All safety and hazard notices on the ma-

chine must be kept in a completely legible

condition.

• When the machine is being used in a closed

room, an extraction unit has to be connect-

ed.

• Use an extraction unit to remove shavings or

saw dust. The ow rate at the extraction port

must be 20 m/s. Negative pressure 1200 Pa.

• For work in a commercial area, a deduster

has to be used. Do not switch off or remove

extraction units or dedusters when the ma-

chine is running.

• Use the machine in a technically awless

condition only, as well as for its intended

purpose, in a safe manner and being aware

of dangers, in compliance with the operating

instructions! Failures which can affect safety

in particular must be removed straight away!

• The manufacturer’s stipulations concerning

safety, work and maintenance as well as the

measurements specied in Technical data,

must be complied with.

• The relevant accident prevention stipula-

tions and other widely recognised safety

rules must be observed.

• The machine may be used, maintained or

repaired only by expert personnel who are

familiar with it and its dangers. Unauthor-

ised changes to the machine invalidate the

manufacturer’s liability for damages result-

ing from this.

• The machine may be used only with the

manufacturer’s original accessories and

original tools.

• Every use beyond that is deemed as not

intended. The manufacturer is not liable for

damage resulting from this, the risk lies ex-

clusively with the user.

Residual risks m

• The machine has been built according to

the latest technology and recognised safety

rules. However, individual residual risks can

occur when working: Risk of injury to ngers

and hands from the rotating cutterblock dur-

ing incorrect handling of the work piece.

Never reach with your hands under the

cutter block guard when guiding the work

piece! Do not pull the work piece back over

the unguarded cutter block.

• Injuries when the work piece is ejected dur-

ing incorrect mounting or handling, such as

working without a fence.

• Health risk from wood dust and shavings.

• Make sure you wear personal protective

equipment such as eye protection and a

dust mask. Use an extraction unit!

• Health risk from noise during work, the per-

mitted noise level is exceeded. Make sure

you wear personal protective equipment

such as hearing protection.

• Electrical hazards when unsuitable electric

connections are used

• Process chosen wood only, without imper-

fections such as: Knots, transverse cracks,

surface cracks, foreign objects (nails,

screws). Flawed wood creates a risk during

work.

• Furthermore, despite all measures taken,

residual risks can occur that are not obvious.

• Residual risks can be minimised by comply-

ing with the safety notices and the intended

use as well as the operating instructions

overal

• Drawing-in/trapping hazard by power feed

mechanism.

• Squeezing hazard by work piece power-

outfeed.

Set-up

Prepare the work place where the power tool

will be used. Make sufcient space so that

safe and uninterrupted work is ensured. The

power tool has been designed for work in

closed rooms, and it has to be set up on an

even, level, solid surface in a stable position.

Fixing the machine on level hard concrete oor

before operation.

Equipment g. 1

1. Jointer table xed

2. Jointer table adjustable

3. Jointing fence

4. Cutterblock cover

5. Table adjustment lever

6. Locking handle for thicknessing table

7. Infeed locking lever

8. Extraction hood

9. Table locking system

10. Thicknessing table clamping

11. Height adjustment caster

12. Handles to adjust the height of the

jointer tables

13. On-/off-switch

Assembly

Due to packaging reasons, your planer is

not completely assembled.

The planer must not be lifted by the jointer ta-

bles!

Attaching and adjusting of base plates

g. 2

Attach 4 base plates to the bottom of the frame,

Slightly tighten hexagon nuts by hand.

In order to balance out an uneven surface,

loosen the lock nuts and turn the base plates

in or out accordingly.

Tighten the lock nut again.

Warning!

Make sure you align the machine using a

spirit level.

Attaching the jointing fence g. 3

Insert the jointing fence (3) in the track and

tighten it with the clamping lever (A).

Adjusting the jointing fence g. 3.0, 3.1

1. Loosen the clamping lever (B).

2. Using a try-square, determine the 90° an-

gle of the jointer table to the stop surface,

3. tighten the clamping lever (B).

4. Loosen the lock nut, adjust the fence with

the cylinder screw (C).

5. Tighten the lock nut again.

Warning!

The jointing fence always has to be se-

cured safely.

Clamping is carried out with the clamping le-

vers (A + B) g 3.1.

Attaching the cutterblock cover g. 4

Attach and tighten the cutterblock cover on the

side of the jointer table with 2 Allen screws.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach Plana 4.1C in the language / languages: English, German, Dutch, French, Finnish as an attachment in your email.

The manual is 7.95 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach Plana 4.1C Manual

Product: