782085

Scheppach Plana 3.0 Manual

16
Zoom out
Zoom in
Previous page
1/128
Next page
english 15
Dull planer blades raise the risk of accidents, the work
efficiency is no longer guaranteed. Bevel the blade only
up to 15 mm knife height. The blade cutting angle should
avarage 40 ± 2 degrees.
For regrinding, bring the blade to an authorised grinding
workshop, or ship it back to the manufacturer.
Installing planer blades Fig. 16
1 Adjusting screw
2 Pressure screw
3 Planer blades
4 V-ledge
5 Markings
6 Adjust gauge
Make sure during installation that
• the risk of injury for fingers and hands is mounted.
• the clamping surface in the cutter spindle and the
Vledge are clean.
• the beveled planer blades are deoiled.
• only blades that have been beveled in a pair are in-
stalled.
• the installation of the planer blades and the V-ledge
correspond to the illustration
• close the planer blades and the V-ledge on both sides.
• all of the clamping screws are tightened (8,9 N/m).
Warning! The details of blade fastening, blade pro-
tection length, blade thickness, should be kept for a
minimum during warm up spin and optimally for the
starting of the blade attachment screw.
Planer blade adjustment, Fig. 17
• To adjust, apply the provided adjustment gauges.
• First, adjust one blade, then the other.
• Shift the blade on the adjusting screw, alternating
sides, till the cutting edge that lies over the work ta-
ble touches the adjustment gauges.
• The right marking must align, corresponding to the il-
During spinning the planer blade must be in sync with
the adjustment gauges as much as possible, optimally
to the second marking.
• Left and right adjustment should be done following the
exterior of the blades.
• Tighten the pressure screws of the V-ledge with a flat
wrench SW 8. (8,9 N/m)
• Adjust and clamp the second blade in the same way.
• Perform a test run after each blade change and then
retighten the pressure screws. (8,9 N/m)
The planer blade must be tested before use to make sure
that the above mentioned instructions have been followed.
Please be attentive of all the safety warnings before turn-
ing the machine on.
Declaration of compliance (EU)
Hereby we, the Scheppach Manufacture of Woodworking Machines
GmbH, Günzburger Str. 69, D-89335 Ichenhausen, declare that the
subsequent qualified machine by way of its construction and design
as well as commercial use meets the corresponding regulations of the
EG-guidelines stated below. In case of a modification of the machine
this declaration is no longer valid.
The machine corresponds to the tested sample.
Name of the machine:
Thicknessing and Planing machine
Type of machine
Plana 3.0, Art.-Nr. 1902202901, 1902202902 , 1902202903
Relevant EC directives:
EC machine directive 2006/42/EG,
EC Low voltage directive 2006/95/EWG,
EC-EMV directive 2004/108/EWG.
Applied harmonized European standards:
EN 55014, EN 55104, EN 60555-2, EN 60204-1, EN 861, EN 847-1, EN
12100-2
Notified body:
Technical Committee on Wood, 70504 Stuttgart; Checking and certifying
body BG-Approval certificate
Place, Date:
Ichenhausen, 28.03.2012
Signature:
Werner Hartmann (Head of technical Innovation - documentation repre-
sentative)
Trouble shooting
To repair faults, switch off the machine. Pull power plug.
Problem Possible Cause Relief
Irregular and discontinuous transport
at the thickness planing
Thickness desk not free of resin or
not free of oil.
Clean and spray (sliding spray) the
thickness desk regularly. This is
valid especially for wet and resinous
woods.
Workpiece shoulder at the planing This is due to badly adjusted planer
knives.
The adjustment of the planer knives
has to be carried out with a lot of
care with help of the adjustment
gauge.
Workpiece inaccuracy at the planing
(concave, convex)
At not exactly parallel standing
trimming desks due to improper
transport or similar.
Adjust the stiff trimming desk 1 mm
above the planing shaft body, as well
as parallel to the bottom plate.
Electrotechnical maintenance only by electric specialists!
At waste disposal of the machine all the local legal regulations have to be kept.
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach Plana 3.0 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach Plana 3.0 in the language / languages: All languages as an attachment in your email.

The manual is 11.5 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info