Manual Scheppach Plana 3.0 (page 11 of 128) (All languages)

782085

Zoom out

Zoom in

1/128

10 english

MANUFACTURER:

Scheppach

Manufacturer of Woodworking Machines GmbH

Günzburger Straße 69

D-89335 Ichenhausen

VALUED CUSTOMER,

We hope that you enjoy your new machine and wish you

every success in working with it. Warning: The manufac-

turer of these devices is not liable, under the applicable

Product Liability Act, for damages to this device or by this

device resulting from:

• improper handling,

• noncompliance with the operating instructions,

• repairs by a third, non-authorized party

• installation and replacement of non-original spare

parts,

• utilization, noncompliant with the regulations,

• failure of the electric equipment resulting from viola-

tion of the electric speciﬁcations and VDE (Association

of Electrotechnology) regulations 0100, DIN 57113 /

VDE 0113.

We advise you:

Before assembly and implementation, please read the op-

erating instructions in their entirety. These operating in-

structions should make it easier for you to get acquainted

with your machine and to use it as intended.

The operating instructions contain important indications

that will help you work professionally and efﬁciently with

the machine, at the same time avoiding risks, saving on

repair costs, decreasing downtime and increasing reliabil-

ity and lifespan of the machine.

In addition to the safety regulations provided in the oper-

ating instructions, you must observe the applicable regu-

lations of your country for the use of this machine. You

should keep the operating instructions near the machine.

They are protected from dirt and moisture by a plastic cov-

ering. These must be read and followed diligently by any

operator, before staring the work. Only those, who have

been instructed on the use and informed of all the as-

sociated risks, should work on the machine. Minimum age

requirements should be observed.

General Considerations

• After unpacking, please check all of the parts for any

possible damages in transit. The feeder must be im-

mediately notiﬁed of any complaints. Late claims will

not be accepted.

• Check that the shipment is complete.

• Before use, familiarize yourself with the operating in-

structions.

• Please use only original parts as supplies, such as

wear and tear and replacement parts. You can obtain

replacement parts from your specialized dealer.

• When ordering, please give our item number, as well

as the type and the year of manufacture of the device.

Plana 3.0

Scope of delivery

Planing machine Plana 3.0

Planer shaft guard

Combined extraction outlet

Assembly supplies (supply

bag)

Adjustable planer fence

Operating instructions

Technical Specs

Dimensions L x W x H mm

(dimensions with baseframe in

brackets)

1160 x 690 x 720 (1060)

Table Height mm 540

Work Table L x W mm je 500 x 310

Thicknessing Table L x W mm 590 x 250

Weight kg 135

Planer shaft

Planer shafts ø mm 59

Knife range ø mm 61

Material of shaft C45

Speed max. 1/min 6500

Number of blades 2

Dimension of blades mm 3 x 18 x 260

Blade resharpable size mm 15

Material of blades mm HSS Nr. 3343

Feeder

No. of feeder cylinders 2

Surface gummed

Feeder cylinders ø mm 35,5

Length mm 307

Feeding speed m/min. 5,0

detachable yes

Motor

Motor V/Hz 380–420/50 220–240/50

Receiving capacity P1 W 2400 2340

Delivering capacity P2 W 1800 1750

Speed 1/min 2800

Operation mode S6/40 %

Work data

Planer work width max. mm 260

Chip work thickness max. mm 3

Planer thickness width max.

mm 250

Chip thickness max.mm 5

Aperture thickness min/max.

mm 5/210

Angle 90–45°

Stopper length mm 900

Stopper height mm 150

Subject to technical changes!

SOUND CHARACTERISTICS

In accordance with EN 23746 for sound power level, as

well as EN 31202 (correction factor k3 calculated ac-

cording to Appendix A.2 of EN 31204) for the calculation

of the sound pressure level at the workstation, the sound

emission values add up to a total below the underlying

work conditions mentioned in ISO 7904 Appendix A.

Sound power level in dB (Work)

Idle speed LWA = 93.8 dB (A)

Processing LWA = 100.6 dB (A)

Sound pressure level at the workstation in dB

Idle speed LpAeq = 88.0 dB (A)

Processing LpAeq = 93.7 dB (A)

Sound power level in dB (Thickness)

Idle speed LWA = 94.8 dB (A)

Processing LWA = 97.9 dB (A)

Sound pressure level at the workstation in dB

Idle speed LpAeq = 78.3 dB (A) Processing LpAeq = 84.3

dB (A)

The speciﬁed values are emission values and therefore

do not have to represent exact work station values at the

same time. Although there is a correlation between emis-

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach Plana 3.0 in the language / languages: All languages as an attachment in your email.

The manual is 11.5 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach Plana 3.0 Manual

Product: