Manual Scheppach Plana 3.0 C (page 14 of 36) (English, German, French)

782087

Zoom out

Zoom in

1/36

12 english

– 45°, where the pivoting segment must be loosened.

Check each model item with a protractor for dimension

accuracy after every angle adjustment.

Planer fence setup, Fig. 4

Check the 90°/45° angle and set the cylinder head screws

M4x8.

1 = Set screw 90° angle

2 = Set screw 45° angle

Attention!

The planer fence must always remain ﬁrmly ﬁxed.

Fig. 5

The clamping of the planer fence results from the exocen-

tric lever.

The planer fence is 260 mm adjustable over the planer.

Attention!

The planer fence must always remain ﬁrmly ﬁxed.

Planer shaft guard, Fig.6

Screw on the planer shaft guard onto a hinged work table.

The planer shaft guard can be deviated without a tool by

pulling the exocentric lever upwards, swaying the shaft

guard, pulling the exocentric lever back down.

Fig. 7 + 8

Attention: Never work with planer fences without the shaft guard.

Operating Instructions

Preparing and setting up the machine

• Changes, setup, measuring and cleaning work on the

machine should only be done with the motor turned off.

Disconnect the power plug and wait for the shutdown of

the rotating tools.

• After repairs and servicing, all protective and safety

equipment must be immediately assembled.

• Immediately exchange defective planer knives (rifts or

such). Monitor the knife change!

• Check the effectiveness of the anti-kickback attachment

before each operation. The gripper taper must have a

sharp edge.

• After repairs and servicing, all protective and safety warn-

ings must be immediately mounted onto the machine.

Thickness and work

• Maximal planer shaft speed 4000 1/min

• The planer shaft has been manufactured in accordance

with DIN EN 847-1.

• Begin the working operation only when the full speed is

reached.

• Keep the operator station free of shavings and wood

waste.

• Employ the extraction unit for extraction of shavings and

wood dust. The velocity of ﬂow of the extraction support

must amount to min. 20 m/s.

• Work only with sharpened planer knives. Dull planer

knives increase the risk of relapse.

• When processing long work pieces (longer than the feed-

ing table) roll racks (optional equipment) should be em-

ployed.

• Work: When dressing a work piece up to 100 mm thick,

the planer shaft guard must cover the work piece and the

planer shaft from above. If the work piece width is more

than 100 mm, set the protective rails of the shaft guard

to the width of the work piece. Make sure to put closed

hands, with the thumb adjacent on the work piece.

• Joining: The work piece is set against the work stopper.

Set the rails of the shaft guard to the width of the work

piece and leave on the table.

• Dressing and joining of small cross sections (strips):

When dressing the work piece, same as for work pieces

up to 100 mm thick, it should be fed with spread out

hands. When joining, push the work piece with both

hands, with the ﬁsts closed, against the help stopper

(optional equipment) and feed it through. The guard de-

vice is positioned near by and rests on the work piece.

• Dressing and joining of small work pieces: When dress-

ing, push the work piece with spread out hands to the

work table and feed through with the pusher, using the

right hand. The left hand slides over the guard device,

as long as the work piece is on the table the weight of

the left hand will shift onto the receiving table. When

joining, push the work piece with the left hand, with the

ﬁst closed, against the help stopper and the table, then

feed through with the pusher.

• Chamfering or beveling: The work piece should be leaned

against the work stopper. Set the protective rails of the

shaft guard to the the width of the work piece and leave

the piece on the table. Push the work piece with the left

hand, with the ﬁst closed, against the stopper and the

receiving table and feed it through with the right hand

closed.

Beginning

Before starting, observe the safety warnings. All guard and

help devices must be installed.

Changes, setup, measuring and cleaning work on the ma-

chine should only be done with the motor turned off.

Disconnect the power plug!

Planer work – Chip removal, Fig. 9, Fig. 9.1

The stock removal can be adjusted from 0 to 5 mm using the

turning handle.

Caution !

Release the blocking handle Fig .9

Read the depth of the stock removal on the graduated ruler,

adjust the table height using the turning handle Fig.9.1.

Tighten the blocking handle Fig.9

Planer work – Planer shaft guard, Fig. 7

When dressing up to 100 mm work piece strength, the

planer shaft guard must cover the work piece and the plan-

er shaft from above. If the work piece width is more than

75 mm, set the protective rails of the shaft guard to the

width of the work piece. Make sure to put closed hands,

with the thumb adjacent on the work piece.

1 Surfacing angle guide

2 Planer shaft guard

Joining, Fig. 8

Use the work stopper for this purpose, leave the planer

shaft protector on the table and set the protective rails to

the width of the work piece.

Push the work piece against the planer stopper and then

lead it over the planer shaft with both hands. As long as

the board reaches high enough on the receiving table, put

the left hand on it and shift it without interruption over the

blade shaft.

Planer work – Shavings emission, Fig. 10

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach Plana 3.0 C in the language / languages: English, German, French as an attachment in your email.

The manual is 5.39 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach Plana 3.0 C Manual

Product: