644549
5
Zoom out
Zoom in
Previous page
1/20
Next page
5
TO SAW:
1 Set the saw on the guide rail.
2 Switch on the machine.
3 Press the saw slowly down to the set cut depth and
move this evenly forward along the rail.
PLUNGE CUTS:
To Saw:
1 Set the saw on the guide rail at the marked cutting
point
2 Secure the rebound protection or fence (accessory not
included) at the back and front cut points on the guide
rail.
3 Switch on the machine.
4 Press the saw down slowly to the set cut depth and
move this forward evenly on the rail up to the front
cutting point.
Tilt Protection:
For miter cuts, it is advisable to install a tilt protection
(accessory not included). This prevents the machine from
tilting to one side while in an oblique position.
Injuries to the body or damage to the machine can be
avoided thereby.
ACCESSORIES
Guide System
1 Piece Guide Rail 1400 mm
ACCESSORY PACKAGE I:
2 Pieces Screw Clamps
1 Piece Rail Joiner
1 Piece Rebound Protection (Fence)
ACCESSORY PACKAGE II:
1 Piece Tilt Protection
Guide Device (Fig. 1.1, 1.2)
The guide rails (A) enable clean, precise cuts
and protect the surfaces from damage.
When sawing with the guide rail, the cut depth is 4.5 mm
less than the scale value on the machine.
For safety, the guide rail can be secured with screw
clamps (B).
The tilt protection (C) prevents the plunge saw from tilt-
ing during
miter cuts and adjustment work.
The rebound protection (D) ensures a safe guiding during
plunging
into the workpiece.
By means of the rail joiner (F), 2 guide rails can be con-
nected and
allow long, precise cuts
The guide clearance of the assembly on the guide rail can
be regulated
with the two adjustment screws (E).
With the offered accessories, miter cuts, corner cuts and
other fi tting
tasks can be carried out.
Splinter Protection
The guide rail comes with a splinter guard, which must
be fi tted before the fi rst use.
1 Secure rail with the screw clamps to a piece of scrap
lumber.
2 Adjust the guide clearance on the rail with the two
adjustment screws (E).
3 Set the plunge saw to ca. 6mm cut depth
4 Set up the saw at the back end of the rail.
5 Switch on the machine, press down to the set cut depth
and fi t the splinter guard along the whole length in one
pass without stopping.
The edge of the splinter guard now corresponds exactly
to the cutting edge of the saw blade
Caution!
Always secure the workpiece in such a way that it cannot
shift.
Always move the machine forward; never pull it toward the
body.
BA divar 55 Zubehör.indd 5BA divar 55 Zubehör.indd 5 03.08.11 12:4703.08.11 12:47
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach PL75 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach PL75 in the language / languages: All languages as an attachment in your email.

The manual is 1,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Scheppach PL75

Scheppach PL75 User Manual - English, German, Dutch, Danish, French, Italian, Swedish - 84 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info