644549
20
Zoom out
Zoom in
Previous page
1/84
Next page
20 GB
19. Trouble shooting
Problem Possible Cause Help
The motor does not run. Faulty motor, power supply cable or plug. Burned
out fuses.
Have the machine checked by skilled
personnel. Do not try to repair the machine
yourselves as it may be dangerous. Check
the fuses and replace them if necessary.
The motor starts slowly
and does not reach running
speed.
Low power supply voltage. Damaged windings.
Burned out capacitor.
Ask for the Electricity Board to check the
voltage available. Have the machine motor
checked by skilled personnel. Have the ca-
pacitor replaced by skilled personnel.
Excessive motor noise. Damaged windings. Faulty motor. Have the motor checked by skilled person-
nel.
The motor does not reach
full power.
Overloaded circuit due to lighting, utilities or other
motors.
Do not use other utilities or motors on the
circuit to which the plunge cut saw is con-
nected.
Motor overheats easily Overload of the motor; inadequate cooling of the
motor
Prevent overloading the motor when cutting;
remove dust from the motor to ensure an
optimum cooling of the motor
Decrease in cutting power
when sawing
The saw blade is too small (sharpened too often) Re-adjust the end stop of the saw unit
The saw cut is rough or
wavy
The saw blade is dull; the tooth shape is not
suited to the thickness of the material
Re-sharpen the saw blade or use an appro-
priate saw blade
The work piece rips or
splinters
The cutting pressure is excessive or the saw
blade is not suited to the application
Use the correct saw blade
REGULAR MAINTENANCE
The regular maintenance decribed above and in the
para graph below can be carried out by unskilled person-
nel.
Do not oil the plunge cut saw, cause cutting must be
carried out in dry conditions; all rotating parts are self-
lubricating.
During maintenance, wear protective gear if possible
(accident-prevention goggles and gloves).
Remove cuttings when necessary both from the cut-
ting area, work surfaces and support bases.
Use of an aspirator or brush is recommended.
ATTENTION: Do not use compressed air jets!
Regularly check blade conditions: if difculties should
arise during cutting, have it sharpened by skilled per-
sonnel or replace it if necessary.
ASSISTENCE
When in need of skilled personnel for special mainte-
nance, or for repairs, both during and following the gu-
arantee pe riod, always apply to authorized centres for
assistance or directly to the manufacturer if there is no
authorized centre in your area.
Only a qualied electrician is permitted to connect the
machine and complete repairs on its electrical equip-
ment.
In the event of enquiries please specify the following da-
ta:
Motor manufacturer
Type of current of the motor
Data recorded on the machine’s rating plate
Data recorded on the switch’s rating plate
18. Maintenance
If specialist personnel must be brought in for extra-
ordinary ser vice or repairs during the warranty peri-
od and thereafter, please contact a service provider
recommended by us or con tact the manufacturer di-
rectly.
Overhauls, maintenance work, cleaning, as well as the
eli mi nation of any malfunctions must only be underta-
ken af ter turning off the motor.
All protective and safety equipment must be reins-
talled immediately upon completion of any repair or
maintenance work.
20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach PL75 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach PL75 in the language / languages: English, German, Dutch, Danish, French, Italian, Swedish as an attachment in your email.

The manual is 1,66 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Scheppach PL75

Scheppach PL75 Additional guide - All languages - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info