781917

Scheppach PC 1300 Kity Manual

29
Zoom out
Zoom in
Previous page
1/188
Next page
29
Wymiana oleju silnika . Rys. 5.
Po raz pierwszy należy wymienić olej silnika po 20 go-
dzinach pracy, każda następna wymiana oleju musi na-
stąpić po każdych kolejnych 100 godzinach.
1 Zdjąć przewód elastyczny D i zlać olej do odpowiedniego
naczynia.
2 Otworzyć zbiornik oleju i osuszyć z oleju miernik po-
ziomu oleju.
3 Podłączyć ponownie przewód elastyczny.
4 Wlać olej, sprawdzic jego poziom przy pomocy miernika
i zamknąć zbiornik.
5 5x szarpanka powoli, tak, że olej jest rozprowadzany
(bez zapłonu)
Zalecany rodzaj oleju silnikowego to SAE 10W-30
Zużyty olej należy zdeponować zgodnie z obowiązującymi w
kraju użytkowania przepisami.
Niedozwolone jest spuszczanie zużytego oleju bezpośrednio
na ziemię lub mieszanie go z innymi odpadami.
Important hint in case of sending the plates to a service
station:
Due to security reasons please see to it that the vibratory
plates are sent back free of oil and gas!
To remove the oil proceed as follows:
1 Zdjąć przewód elastyczny D i zlać olej do odpowiedniego
naczynia.
2 Otworzyć zbiornik oleju i osuszyć z oleju miernik po-
ziomu oleju.
3 Podłączyć ponownie przewód elastyczny.
Wymiana oleju w mimośrodzie rys. 6-8.
Po 200 roboczogodzinach należy wymienić olej w mi-
mośrodzie!
1. Wymianę oleju przeprowadzać wyłącznie przy schło-
dzonym mimośrodzie.
2. Zdjąć osłonę pasa klinowego (1) oraz pas klinowy (2).
3. Odkręcić śruby (3) obudowy mimośrodu.
4. Całą część górną wibratora płytowego wraz z silnikiem
zdjąć z obudowy mimośrodu (4).
5. Na górze mimośrodu usunąć śrubę spustową oleju (5),
przechylić obudowę mimośrodu (4), a olej spuścić do
wanny. Olej skontrolować pod kątem obecności wiórków
metalowych, by w przyszłości uniknąć problemów.
6. Obudowę mimośrodu (4) ustawić ponownie w odpo-
wiedniej pozycji.
7. Obudowę mimośrodu (4) napełnić specjalnym olejem
(do PC 800 wlać 0,06l, do PC 1100 wlać 0,08l +
PC 1300 wlać 0,1l)
Zalecany olej do mimośrodu to SAE 10W-30 lub
10W-40
Uwaga! Nie palić i nie pracować w pobliżu otwartego
ognia.
Niebezpieczeństwo wybuchu!
Changing the motor oil. Fig. 5.
After 20 operating hours, the oil must be changed for
the rst time, then every 100 operating hours.
1 Remove the exible hose D and poor the oil into a
suitable bin.
2 Open the lling cap (measuring stick) and let the
oil drain.
3 Reconnect the exible hose.
4 Fill the oil in, check with the measuring stick, and
close.
5 pull starter slowly for 5 times, so that the oil spreads
(without ignition)
Recommended motor oil SAE 10W-30
Dispose of waste oil according to your country’s regula-
tions.
It is not allowed to drain waste oil onto the ground or mix
it with other waste material.
Important hint in case of sending the plates to a ser-
vice station:
Due to security reasons please see to it that the vibratory
plates are sent back free of oil and gas!
To remove the oil proceed as follows:
1 Remove the exible hose D and poor the oil into a
suitable bin.
2 Open the lling cap (measuring stick) and let the
oil drain.
3 Reconnect the exible hose.
Changing the oil in the eccentric vibration unit Fig.
6-8.
Change the oil in the eccentric vibration unit after
200 operating hours!
1. Only change the oil once the eccentric vibration unit
has cooled.
2. Remove the V-belt cover (1) and the V-belt (2).
3. Loosen the screws (3) on the eccentric vibration unit
housing.
4. Lift the entire upper part of the plate vibrator with the
engine off the eccentric vibration unit housing (4).
5. Remove the oil drain screw (5) from the top of the
eccentric vibration unit, tip the eccentric vibration unit
housing (4) and drain the oil into a collection pan.
Check the oil for any swarf, in order to avoid future
problems.
6. Return the eccentric vibration unit housing (4) to an
upright position.
7. Re-ll the eccentric vibration unit housing (4) with oil
recommended for eccentric vibration units (ll the PC
800 with 0.06l, ll the PC 1100 with 0.08l +
PC 1300 with 0.1l)
Recommended oil for the eccentric vibration unit:
SAE 10W-30 or 10W-40
CAUTION! Do not smoke or work near open re.
DANGER OF EXPLOSION!
… 29 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach PC 1300 Kity at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach PC 1300 Kity in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 10.47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info