781931
5
Zoom out
Zoom in
Previous page
1/12
Next page
english 5
Setup
Prepare the workplace where the machine is to be placed.
Ensure sufficient room to allow safe work without malfunc-
tions.
The machine is designed to operate on a level surface and
mustbeplacedsecurelyonrm,levelground.
Please make sure your scheppach machine is placed firmly
on stable plain ground.
Assembly
Forpackagingreasons, thebase(6)istobeinstalledby
the customer.
Usethe5saucer-headscrewsM8x12thatareincludedin
the delivery.
Placethedevicehorizontallyontheoor,andputtheSty-
ropor pad of the packaging underneath the splitting wedge
side.
m Electrical connection
The installed electric motor is completely wired ready for op-
eration.
The customer’s connection to the power supply system, and
any extension cables that may be used, must conform with
local regulations.
Important remark:
The motor is automatically switched off in the event of an
overload. The motor can be switched on again after a cool-
ing down period that can vary.
Defective electrical connection cables
Electrical connection cables often suffer insulation dam-
age.
Possible causes are:
• Pinch points when connection cables are run through
window or door gaps.
• Kinksresultingfromincorrectattachmentorlayingof
the connection cable.
• Cuts resulting from running over the connecting cable.
• Insulationdamageresultingfromforcefullypullingout
of the wall socket.
• Cracks through aging of insulation.
Such defective electrical connection cables must not be
used as the insulation damage makes them extremely haz-
ardous.
Check electrical connection cables regularly for damage.
Make sure the cable is disconnected from the mains when
checking.
Electrical connection cables must comply with the regula-
tionsapplicableinyourstate/localjurisdiction.
Single-phase motor
• The mains voltage must coincide with the voltage speci-
edonthemotor’sratingplate.
• Doubleinsulatedtools areequipped withapolarized
plug(onebladeiswiderthantheother.)Thisplugwill
tinapolarizedoutletonlyoneway.Iftheplugdoes
not t fully in the outlet, reverse the plug. If it still
does not t, contact a qualied electrician to install
apolarizedoutlet.Donotchangethepluginanyway.
Warning: Do not permit fingers to touch the terminals of
plug when installing or removing from outlet.
• Double insulation eliminates the need for the three
wire grounded power cord and grounded power sup-
plysystem.Beforeplugginginthetool,becertainthe
outlet voltage supplied is within the voltage marked on
the nameplate.
• The connection to the mains must be protected with a
16 A slow-acting fuse.
Extension cords
• The use of any extension cord will cause some drop in
voltage and loss of power.
• Wiresoftheextensioncordmustbeofsufcientsize
to carry the current and maintain adequate voltage.
• Use the table to determine the minimum wire size
(A.W.G.)extensioncord.
• Iftheextensioncordisworn,cut,ordamagedinany
way,replaceitimmediately.
EXTENSIONCORDLENGTH
Wire Size A.W.G.
Upto58ft. 18
25 to 100 ft. 16
100 to 150 ft. 14
Note: Usingextensioncordsover150ft.longisnotrec-
ommended.
Only a qualified electrician is permitted to connect the
machine and complete repairs on its electrical equip ment.
Intheeventofenquiriespleasespecifythefollowingdata:
• Motor manufacturer
• Type of current of the motor
• Datarecordedonthemachine’sratingplate
• Datarecordedontheswitch’sratingplate
.Operation
Before operating your scheppachmachine,the bleed screw
should be loosened by some rotations until air can go in
and out of the oil tank smoothly. Failed to loosen the bleed
screw will keep the sealed air in hydraulic system being
compressed after being decompressed. Such continuous
compression/decompressionwillblowoutthesealsofthe
hydraulic system and cause permanent damage to your
scheppach machine.
Before moving your scheppach machine, make sure the
bleed screw is tightened to avoid oil leaking from this
point.
Only split plain cut log.
1.Placethelogplainontotheworktable(3).
2. Fix the log pusher in the required position according to
the length of the log.
Position 1: Length up to 201/2”,
Position 2: Length up to 181/2”,
Position 3: Length up to 161/2”.
3.Complyingwithregulationsandforyoursafety,thehy-
draulic log splitter features two-handed control.
Tostartthesplittingprocess,youmustsimultaneously
press the lever (13) with your left hand and the start
button(8)intheswitchboxwithyourrighthand.
Releasing one of the two control elements will immedi-
ately stop the splitting process, releasing both control
elements will abort the splitting process.
Thepressureplate(2)willthenmovebackintoitshome
position.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach OXT500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach OXT500 in the language / languages: English as an attachment in your email.

The manual is 1.7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info