781945

Scheppach OX7-1600 Manual

19
Zoom out
Zoom in
Previous page
1/38
Next page
14 english
Transport
Transport with a fork lift truck:
For shipment, the machine is fi xed to a pallet by steel
bandings. It is protected by a plastic sheet cover.
At least two persons are required to lift it off the pallet.
Tilt it carefully to the side with the wheels and let it glide
off the pallet.
Attention:
The log splitter has a high centre of gravity -
danger of tipping over!
Manual transport
To transport the log splitter, tilt it slightly, until the ma-
chine stands on its wheels and can be moved.
Transport with a crane, fi g. 2
Use the 2 holes A in the upper section of the machine for
the transport on a crane-hook.
Never lift the machine at the
splitting knife!
minimum
maximum
recommended
temperature
5 C°
40 C°
16 C°
humidity
95 %
70 %
At ambient temperatures lower than 5°C, the machine
needs to run at idle speed for about fi ve minutes for the
hydraulic system to reach operating temperature.
Storage conditions
Please ensure the following conditions:
• dry, sheltered storage location
• maximum humidity 80%
• temperature range from -20° C to +60° C
The machine should be operated under the following con-
ditions:
Setting-up
Prepare the location, where the machine will stand. Clear
enough space to ensure safe and trouble-free working.
The machine is designed for operation on level surfaces
and must stand stably on a level, solid underground.
Assembly
For packaging reasons, your machine is not fully assem-
bled.
Insert the provided support rails and secure them.
Montage
Ihre Maschine wird komplett Montiert ausgeliefert.
Function Test
Before every use you should conduct a function test.
Action: Result:
Pressing both handles down.
The splitting knife moves
down - as far as approx. 5 cm
above the table.
Releasing either handle.
The splitting knife stays in its
position.
Releasing both handles.
The splitting knife moves
back into top position.
Operating Instructions
Lever positions on the control valve
Position „0“
Splitting knife moves upwards and automatically to position
“1”
Position “1”
Basic position, no movement at the splitting knife.
When the cylinder is extended and the return-stop is being
activated the knife remains at position “1”. The cylinder does
not retract.
Position “2”
Splitting speed. The splitting knife moves at slow speed and
with highest splitting force.
Rapid motion “3”
Fast speed. The splitting knife moves at highest speed and
with reduced splitting force.
Setting during the raising of the cylinder
Adjust the nut to the lowest hole on the bar for 1 m wood
(Fig. 3).
Always leave the upper nut with spring cotter in this po-
sition!
• Activate the return-stop. Position “1”
• If you are using a splitter with electric motor it is suffi -
cient to press a shift knob.
• To turn on the device, press the green power switch.
• When using a PTO driven splitter please note the follo-
wing:
1. The connection to the cardan shaft must be performed
after the coupling of the PTO lifting unit.
2. The locking of the PTO lifting unit must be secured with
appropriate safeguards.
3. Now connect the drive shaft with the gear shaft and the
PTO connector.
4. Activate the return-stop. Position “1”
5. Switch on the PTO shaft.
• Now operate both control levers carefully in order to
move the cylinder SLOWLY upwards. It is most impor-
tant that you pay attention to the hydraulic hoses!
• When the cylinder plate is at the boom, release one con-
trol lever and keep the other one still pressed.
• Switch off the machine. Now you can secure the screws
0
1
2
3
1
… 19 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach OX7-1600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach OX7-1600 in the language / languages: English, German, French as an attachment in your email.

The manual is 11.61 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info