Manual Scheppach OX 7-1620 (page 21 of 53) (English, German, French)

781951

Zoom out

Zoom in

1/53

Montage

Your log splitter is completely assembled

Function test

Before every use you should conduct a

function test.

Action Result

Pressing both handles

down.

The splitting knife mo-

ves down - as far as

approx. 5 cm above

the table.

Releasing either

handle.

The splitting knife

stays in its position.

Releasing both

handles.

The splitting knife

moves back into top

position.

Operating instructions

Lever positions on the control valve (Fig.8)

Position „0“

Splitting knife moves upwards and automatically

to position “1”

Position “1”

Basic position, no movement at the splitting

knife.

When the cylinder is extended and the return-

stop is being activated the knife remains at

position “1”. The cylinder does not retract.

Position “2”

Splitting speed. The splitting knife moves at slow

speed and with highest splitting force.

Position “3”

Fast speed. The splitting knife moves at highest

speed and with reduced splitting force.

Setting during the raising of the cylinder

Adjust the nut to the lowest hole on the bar for

1 m wood (Fig. 3).

Always leave the upper nut with spring cotter in

this position!

• Activate the return-stop. Position “4”

• If you are using a splitter with electric motor

it is sufcient to press a shift knob.

• To turn on the device, press the green

power switch.

• When using a PTO driven splitter please

note the following:

1. The connection to the cardan shaft must be

performed after the coupling of the PTO

lifting unit.

2. The locking of the PTO lifting unit must be

secured with appropriate safeguards.

3. Now connect the drive shaft with the gear

shaft and the PTO connector.

4. Activate the return-stop. Position “4”

5. Switch on the PTO shaft.

• Now operate both control levers carefully

in order to move the cylinder SLOWLY

upwards. It is most important that you pay

attention to the hydraulic hoses!

• When the cylinder plate is at the boom, re-

lease one control lever and keep the other

one still pressed.

• Switch off the machine. Now you can secu-

re the screws with the nuts in order to lock

the cylinder (Fig. 4).

• The nuts and the washers are located on

the control levers (Fig. 4.1)

• Never move upwards quickly, do not apply

force!

• Errors in handling and operation are hereby

explicitly excluded from the warranty.

• Now release the operating knobs, the

splitting wedge is pulled upwards by the

plunger. The wood splitter is now ready for

use.

Only use cardan shafts with CE signs,

declaration of conformity and operating inst-

ructions! Read these operating instructions

carefully prior to operation!

Perform the above procedures only when

the motor and the PTO connector are turned

off and the ignition key is removed!

Adjustment during the lowering of the

cylinder

• Adjust the nut to the lower hole on the bar.

Lower the splitting knife onto a piece of

wood of about 15 cm height, switch off the

machine. Fig. 6

• Unfasten the screw nuts on the cylinder,

press an operation knob, and turn on the

machine.

• Release the operation knob slowly. Lower

the cylinder slowly, and switch off the

machine.

Splitting

• At temperatures below 5°C leave the ma-

chine at idle speed for about ve minutes

so that the hydraulic system reaches opera-

ting temperature.

• Place the wood under the splitting knife in

an upright position und press against the

xing bolt.

• Warning. The xing bolt and the splitting

knife are very sharp. Risk of injury!

• When you press down both operating levers

simultaneously, the splitting knife moves

down and splits the wood.

• Only split timber that has been cut straight.

• Split the wood vertically.

• Never split wood horizontally or diagonally!

• Wear appropriate gloves while splitting

wood.

Length of wood

The hydraulic splitter is suitable for the split-

ting of short wood and wood by the metre. It is

practical to adjust the upper stroke limitation to

3 to 5 cm.

Lifting limitation

• If you have logs of wood with a length of

more than 100 cm place the nut in the up-

per hole of the bar (Fig. 3) and clamp with

the locking pin.

• If you have logs of wood with a length of

less than 65 cm place the nut in the middle

hole and clamp with the locking pin.

Start-up

Make sure that the machine is completely and

properly assembled. Before every use, check:

• the power cords for faults (cracks, cuts and

such),

• the machine for possible damages,

• if all bolts are fastened tightly,

• the hydraulic system for leaks, and the oil

level.

Power on/off

Press the green button to power on.

Press the red button to power off.

Note: Check the function of the on/off-unit befo-

re every use by switching it on and off once.

Restart cut-out in case of power failures (zero

voltage switch)

In case of a power failure, unintentionally pulling

the power plug or a defect fuse the machine will

automatically switch off. To restart the machine,

press the green button on the switchbox again.

Operation with Tractor‘s Hydraulics

• Before putting the machine into service,

make sure that the power cables are not

DGB

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach OX 7-1620 in the language / languages: English, German, French as an attachment in your email.

The manual is 3.51 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach OX 7-1620 Manual

Product: