Manual Scheppach OX 7-1020 (page 20 of 53) (English, German, French)

781949

Zoom out

Zoom in

1/53

Accident prevention standards m

The machine may only be operated by qualied

personnel who are well aware of the contents of

this manual.

Before operating the machinery, you must check

the integrity of the safety mechanisms and ensu-

re that they are working properly.

Also before operation, you should familiarise

yourself with the machine controls, following the

operating instructions.

The specied capacity of the machine must not

be exceeded. Under no circumstances the

machine must be used for anything else but its

indented use.

All personnel must wear work clothes as stated

in the regulations of the country in which the

machine is operated. Wide, loose clothing, belts,

rings, and necklaces should not be worn. Long

hair should be tied back.

Try to keep the working area tidy at all times.

Tools, accessories, and spanners should be

kept within reach.

During cleaning or maintenance work the machi-

ne must not be connected to the mains supply.

It is strictly prohibited to operate the machine

without safety mechanisms or with safety me-

chanisms disengaged.

It is strictly prohibited to remove or modify

safety mechanisms.

You should not carry out any maintenance or

adjustments before having carefully read this

manual.

The given maintenance schedule must be

observed for safety reasons as well as to ensure

that the machine performs properly.

The warning labels must be always clean and

legible and must be observed in order to avoid

accidents. If labels are damaged or missing or

belong to parts that were replaced, then those

labels must be replaced by original labels orde-

red from the manufacturer and be attached at

the positions prescribed.

In case of re, dry powder re extinguishing

agents must be used. A burning machine must

not be extinguished with water because of the

risk of a short circuit.

If the re cannot be extinguished immediately,

watch for liquids leaking.

During a longer re the oil tank or the pressu-

rised lines can explode: Therefore make sure

that you are not getting into contact with the

leaking liquids.

Dismantling and Disposal

The machine does not contain any materials

that are hazardous to health or the environment,

because it is manufactured from materials that

are either completely recyclable or can be dispo-

sed in a normal way.

For disposal, you should use specialist com-

panies or qualied personnel, who know the

possible risks and have read these operating

instructions and follow them precisely.

If the machine falls into disuse, follow these

steps under observance of all applicable acci-

dent prevention measures:

• Disconnect the energy supply (electrical or

PTO),

• Remove all electrical wires and hand over

to a specialised collecting point, while

observing national regulations.

• Drain the oil tank and deliver the oil in a

closed container to a collecting point, while

observing national regulations.

• Deliver all other machine parts to a scrap

collection point, while observing national

regulations.

Make sure every part of the machine is disposed

of in accordance with all applicable national

regulations.

Residual risks m

The machine was designed according to the

state of the art and accepted safety stan-

dards. However, residual risks might occur

during work.

• Risk of nger or hand injury by the cutting

knife due to improper guidance or place-

ment of the log.

• Injuries by the work piece being catapulted

out of machine due to improper clamping or

guidance.

• Electrical hazard due to use of improper

power cords.

• Furthermore there might be non-obvious

remaining risks despite all precautions.

• Residual risks can be reduced if safety

instructions, intended use, as well as all

operating instructions are observed.

Equipment Fig.1

1. Control lever

2. Wood retaining lever

3. Control valve

4. Backstop

5. Retaining arm

6. Splitting knife

7. E-motor with switch

8. Carrying wheel (without the three-point system)

9. Three-point hitch

10. Log lifter

Transport / Storage conditions

Transport with a fork lift truck:

For shipment, the machine is xed to a pallet by

steel bandings. It is protected by a plastic sheet

cover.

At least two persons are required to lift it off the

pallet.

Tilt it carefully to the side with the wheels and let

it glide off the pallet.

Attention: The log splitter has a high centre of

gravity - danger of tipping over!

Manual Transport

Transport by hand is permitted only with the

driving device (see Accessories).

To transport the wood splitter,

ip the froe until the machine rests on the wheel

of the driving device and can thus be moved.

Caution, do not transport in the lying posi-

tion!

Transport with a crane, g. 2

Use the 2 holes A in the upper section of the

machine for the transport on a crane-hook. Ne-

ver lift the machine at the splitting knife!

Transport with Tractor

Power take-off must be turned off during trans-

port.

The warning panel with rear light DIN 110030

must be mounted on the wood splitter and the

rear light connected to the tractor.

Please ensure the following conditions:

• dry, sheltered storage location

• maximum humidity 80%

• temperature range from -20° C to +60° C

The machine should be operated under the

following conditions:

mini-

mum

maxi-

mum

recommen-

ded

temperature 5 C° 40 C° 16 C°

humidity X 95 % 70 %

At ambient temperatures lower than 5°C, the

machine needs to run at idle speed for about

ve minutes for the hydraulic system to reach

operating temperature.

Setting-up

Prepare the location, where the machine will

stand. Clear enough space to ensure safe and

trouble-free working.

The machine is designed for operation on level

surfaces and must stand stably on a level, solid

DGB

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach OX 7-1020 in the language / languages: English, German, French as an attachment in your email.

The manual is 3.51 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach OX 7-1020 Manual

Product: