781993

Scheppach MTP860H Manual

26
Zoom out
Zoom in
Previous page
1/64
Next page
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
26 GB
4 Keep all bystanders, children, and pets at least 23m
away. If you are approached, stop the unit immedi-
ately.
5 Walk, never run with the machine.
6 This unit has a clutch. Squeeze the clutch control
lever and check that i t returns automatically to the
neutral position. If it does not, have unit adjusted by
a qualied repair personnel.
7 Disengage clutch lever before starting the engine.
8 Start the engine carefully according to instructions
and with feet well away from the tines.
9 The tines remain stationary when the clutch is disen-
gaged. If it does not, have unit adjusted by a qualied
repair personnel.
10 Always operate the machine from behind, never
pass or stand in front of the machine when the en-
gine is running.
11 Always hold the unit with both hands when operat-
ing. Keep a rm grip on the handlebars.
12 Be aware that the machine may unexpectedly
bounce upward or jump forward if the tines should
strike buried obstacles such as large stones, roots,
or stumps.
13 If the unit strikes a foreign object, stop the engine,
disconnect the spark plug, thoroughly inspect the
machine for any damage, and repair the damage be-
fore restarting and operating the machine.
14 Use extreme caution when in reverse ornpulling the
machine towards you.
15 Do not overload the machine capacity by tilling too
deep in a single pass or at too fast a rate.
16 Never operate the tiller at high transport speeds on
hard or slippery surfaces.
17 Be careful when tilling in hard ground. The tines may
catch in the ground and propel the tiller forward. If
this occurs, let go of the handlebars and do not re-
strain the machine.
18 Use caution when tilling near fences, buildings and
underground utilities. Rotating tines can cause prop-
erty damage or personal injury.
19 Exercise extreme caution when operating on or
crossing gravel drives, walks, or roads. Stay alert for
hidden hazards or trafc. Do not carry passengers.
20 Never leave the operating position when the engine
is running.
21 Always stop the engine when tilling is delayed or
when walking from one tilling location to another.
22 Keep unit clean of vegetation and other materials.
They may become lodged between the tines. Stop
the engine and disconnect the spark plug before un-
clogging the tines.
6. Technical data
Engine: Honda 4-stroke, 196 ccm
Engine rating: 6.5 hp
Engine working speed: 3600 min-1
Working width: 330/500/800mm
Blades diameter Ø: 350 mm
Starting system: Reversing starter
Fuel: Unloaded petrol min. 91oc-
tane max. 10% bio-ethanol
Engine oil: 0.6l (15W40)
Tank capacity: 3.1 l
Weight: 81 kg
Spark plug: NGK BPR6ES
Speed
Forwards:
1. Forward gear 4.70 km/h
2. Forward gear 6.50 km/h
Backwards
Reverse gear 3.50 km/h
7. Assembly
At rst check all parts of the device and place them in
front of you on the oor.
Assembling the Support wheel (12) (Fig.3)
Attach the support wheel (12) to the frame as shown in
gure 3. For this purpose, the two holes (3a + 3b) must
be brought into conformity.
To lock the support wheel in the transport position
(Fig.32):
1. Two holes (3a + 3b) must be brought into conformity,
2. Insert pin (3d) and securing it with cotter
3. Insert pin (3e) and securing it with locking screw (3f)
and the cotter (Fig.3).
After installation, the wheel must look as shown in Fig.3.
To lock the support wheel in the working position
(Fig.33+34):
1. Loosen the support wheel from the holes (3a) and re -
block it in the holes (3c).
After installation, the wheel must look as shown in
Fig.33+34.
Fitting the Blades (Fig.3-5)
Tillage width 800 mm:
The toolholder (3g) has a hexagonal cross-section to en-
able quick installation of the blades (14).
1) Grease the toolholder (3g) and observe the alignment
of the mounting hole (3h) when installing the blades
(14) (Fig.3).
2) Insert the pin (B6, Fig.4) into the opening and secure it
with the cotter.
3) Attach the Milling broadening (15) to the petrol pow-
er cultivator and check the perfect alignment of the
mounting hole (4a).
… 26 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach MTP860H at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach MTP860H in the language / languages: English, German, French, Polish as an attachment in your email.

The manual is 6.35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info