Manual Scheppach MTP560 (page 26 of 156) (English, German, Dutch, French, Italian, Polish, Spanish)

781418

Zoom out

Zoom in

1/156

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

26 | GB

m ATTENTION! Do not use strong detergents or pe-

troleum based cleaners when cleaning plastic parts.

Chemicals can damage plastics.

6. Inspect for any loose or damaged parts. Repair or

replace damaged parts and tighten loose screws,

nuts or bolts.

7. Remove the tines. Clean and apply oil to the tines

and tine shafts to prevent rusting. Mount the tines

onto the tine shafts.

8. Coat the wheel axles lightly with oil. Oil the throt-

tle cables and all visible moving parts. Do not re-

move the engine cover.

9. Store your tiller in upright position in a clean, dry

building that has good ventilation.

m ATTENTION! Do not store tiller with fuel in a

non-ventilated area where fuel fumes may reach

ame, sparks, pilot lights or any ignition sources. Use

only approved fuel containers.

2. Start the engine and allow it to run until it stops.

This ensures no fuel is left in the carburetor. Run

the engine until it stops. This helps prevent plastic

deposits from forming inside the carburetor and

possible engine damage.

3. While the engine is still warm, drain the oil from

the engine. Rell with fresh oil of the grade rec-

ommended in the Engine Manual.

4. Allow the engine to cool. Remove the spark plug

and put 30 ml of high quality motor oil into the cyl-

inder. Pull the starter rope slowly to distribute the

oil. Replace the spark plug.

m ATTENTION! Remove the spark plug and drain all

of the oil from the cylinder before attempting to start

the unit after storage.

5. Use clean cloths to clean o󰀨 the outside of the

tiller and to keep the air vents free of obstructions.

13. Troubleshooting

Problem Possible cause Solution

Motor does not start up 1. The starter is not in the correct position

for the prevailing conditions

2. The reservoir is empty

3. The air lter components are dirty

4. Spark plug is loose

5. Spark plug wire improperly attached or

disconnected from the outlet

6. Incorrect spark plug gap

7. Defective spark plug

8. Carburetor immersed in gasoline - Gas

switch is in the OFF position

1. Move the starter to the appropriate

position

2. Fill the tank

3. Clean the air lter components

4. Tighten the plug to 25-30 Nm

5. Attach the plug wire to the plug

6. Adjust the spacing between the

electrodes to between 0.7 to 0.8

7. Install a new spark plug that is cor-

rectly placed

8. Remove the air lter and pull on the

starter cable continually until the

carburetor cleans itself and reinstall

the air lter Set the gasoline switch

to the position

Motor has trouble starting or

loses power

1. Lighter module defective

2. Dirt, water or mold from the gas tank

3. The hole in the tank stopper is obstruct-

4. The air lter components are dirty

1. Contact the vendor service

2. Drain the reservoir, clean it and ll it

with clean fresh gasoline

3. Clean or replace the tank plug

4. Clean the air lter components

Motor operates irregularly 1. Air lter components are dirty

2. The throttle level is blocked by debris

3. Cooling ns and air passages under the

motor are blocked

1. Clean the air lter components

2. Remove any projectile debris

3. Remove any debris from the cooling

ns and the air passage

Motor locks up at high

speeds

1. The gap between the spark plug elec-

trodes is too small.

1. Adjust the spacing between the

electrodes to between 0.7 and 0.8

Motor overheats 1. Cooling air ow is obstructed.

2. Defective spark plug.

1. Remove all debris from the mount-

ing, ventilator, air passages and

cooling ns

2. Install an LG F6TC spark plug.

Motor vibrates abnormally 1. The tiller has not been properly assem-

bled. The power tiller assembly is not

balanced

1. Check that all parts of the engine

are properly assembled

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach MTP560 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 7.22 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach MTP560 Manual

Product: