Manual Scheppach MTE460 (page 27 of 116) (English, German, Dutch, French, Italian, Polish, Spanish)

781995

Zoom out

Zoom in

1/116

 www.scheppach.com /  service@scheppach.com /  +(49)-08223-4002-99 /  +(49)-08223-4002-58

GB | 27

Transport and storage (g. 10, 12)

Always pull out the power cord before transporting!

Pull the lock pin (17). You can now move the wheels

(7) to the lower position. Make sure that the lock pin

(17) engages again in the lower position. (g. 10)

m Attention! The wheels must be xed in the upper

position during operation!

For storage or transport in a limited space, proceed

as follows:

Open the wing nuts (10) until you can fold the handles

forward. Attention! Danger of crushing your ngers.

Now you can transport your machine with the trans-

port handle (3).

So you can storage the machine too.

9. Electrical connection

The electrical motor installed is connected and

ready for operation. The connection complies

with the applicable VDE and DIN provisions.

The customer‘s mains connection as well as

the extension cable used must also comply with

these regulations.

Damaged electrical connection cable

The insulation on electrical connection cables is of-

ten damaged.

This may have the following causes:

• Passage points, where connection cables are

passed through windows or doors.

• Kinks where the connection cable has been im-

properly fastened or routed.

• Places where the connection cables have been cut

due to being driven over.

• Insulation damage due to being ripped out of the

wall outlet.

• Cracks due to the insulation ageing.

Such damaged electrical connection cables must not

be used and are life-threatening due to the insula-

tion damage.

Check the electrical connection cables for damage

regularly. Make sure that the connection cable does

not hang on the power network during the inspection.

Electrical connection cables must comply with the

applicable VDE and DIN provisions. Only use con-

nection cables with the marking „H05VV-F“.

The printing of the type designation on the connec-

tion cable is mandatory.

AC motor

• The mains voltage must be ~230-240 V / 50 Hz

• Extension cables up to 25 m in length must have

a cross section of at least 1,5 mm² , above 25 m

at least 2,5 mm²

• The mains connection is protected with a 16 A

slow-blow fuse.

Laying the power cord (g. 6, 7)

Mount the cable and the cable guide (11) on the low-

er right bar (4) and (in the working direction) bar (3)

by pushing them on.

Install the transport aid (g. 8, 9)

Remove the pre-assembled split pin (16) and the

washer (15). Place the wheel (7) on the wheel holder

(14). Secure it with the washer (15) and the split pin

(16). Then mount the wheel cap (8). (Assembly is

identical on both sides)

Blade roller installing / uninstalling (g. 11)

Push the blade roller (6) on the drive shaft (20) of the

machine. The blade roller (6) can be mounted left or

right side. Be sure that the holes of the blade roller

(6) and the drive shaft (20) are aligned.

Now the M8 screw (18) is pushed through and se-

cured with the M8 locking nut (19).

Tighten the lock nut (19) hand-tight using a fork

wrench or ratchet with socket (the tools are not in-

cluded).

For uninstall: Proceed in reverse order.

8. Operation

Start and stop the implement (g. 7)

To prevent an accidental start-up of the implement,

the throttle handle (1) is equipped with a safety re-

lease switch (12) which must be pressed before the

On/O󰀨 switch (13) can be pressed. If the On/O󰀨

switch (13) is released, the equipment switches o󰀨.

Repeat this process several times so that you are

sure that the machine functions properly. Before you

perform any repair or maintenance work on the ma-

chine, ensure that the cutting unit is not rotating and

that the power supply is disconnected. Always ensure

that a safe distance (provided by the long handles) is

maintained between the user and the housing.

The safety distance between housing and user given

by the handle (1) must always be observed. Be espe-

cially careful when digging and changing direction on

slopes and inclines.

Maintain a solid footing and wear sturdy, non-slip

footwear and long trousers. Always dig along the in-

cline (not up and down). For safety reasons, the Elec-

tric Tiller may not be used to dig up inclines whose

gradient exceeds 15 degrees. Use special caution

when backing up and pulling the implement (tripping

hazard)!

Tips for proper working

Always guide the machine slowly and wisely forward.

Dig up the area in straight lines. Let the tracks overlap

slightly to not miss any stripes to dig. Only use the

machine to dig up already loosened soil.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach MTE460 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 5.57 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach MTE460 Manual

Product: