Manual Scheppach MT140 (page 20 of 52) (English, German, French)

757078

Zoom out

Zoom in

1/52

 www.scheppach.com  service@scheppach.com  +(49)-08223-4002-99  +(49)-08223-4002-58

20 І 52

b) Use only bonded reinforced or diamond Cut-

ting wheels for your power tool.

Just because an accessory can be attached to

your power tool, it does not assure safe opera-

tion.

c) The rated speed of the accessory must be at

least equal to the maximum speed marked on

the power tool.

Accessories running faster than their rated speed

can break and y apart.

d) Wheels must be used only for recommended

applications. For example: do not grind with

the side of Cutting wheel.

Abrasive Cutting wheels are intended for periph-

eral grinding, side forces applied to these wheels

may cause them to shatter.

e) Always use undamaged wheel anges that

are of correct diameter for your selected

wheel.

Proper wheel anges support the wheel thus re-

ducing the possibility of wheel breakage.

f) Do not use worn down reinforced wheels

from larger power tools.

Wheels intended for a larger power tool are not

suitable for the higher speed of a smaller tool and

may burst.

g) The outside diameter and the thickness of

your accessory must be within the capacity

rating of your power tool. Incorrectly sized

accessories cannot be adequately guarded

or controlled.

h) The arbour size of wheels and anges must

properly t the spindle of the power tool.

i) Wheels and anges with arbour holes that

do not match the mounting hardware of the

power tool will run out of balance, vibrate ex-

cessively and may cause loss of control. Do

not use damaged wheels. Before each use,

inspect the wheels for chips and cracks. If

power tool or wheel is dropped, inspect for

damage or install an undamaged wheel. After

inspecting and installing the wheel, position

yourself and bystanders away from the plane

of the rotating wheel and run the power tool

at maximum no load speed for one minute.

Damaged wheels will normally break apart

during this test time.

j) Wear personal protective equipment. De-

pending on application, use face shield, safe-

ty goggles or safety glasses. As appropriate,

wear dust mask, hearing protectors, gloves

and shop apron capable of stopping small

abrasive or workpiece fragments.

The eye protection must be capable of stopping

ying debris generated by various operations.

The dust mask or respirator must be capable of

ltrating particles generated by your operation.

Prolonged exposure to high intensity noise may

cause hearing loss.

4) Power tool use and care

a) Do not force the power tool. Use the cor-

rect power tool for your application. The

correct power tool will do the job better and

safer at the rate for which it was designed.

b) Do not use the power tool if the switch

does not turn it on and off. Any power tool

that cannot be controlled with the switch is

dangerous and must be repaired.

c) Disconnect the plug from the power source

and/or the battery pack from the power tool

before making any adjustments, changing

accessories, or storing power tools. Such

preventive safety measures reduce the risk of

starting the power tool accidentally.

d) Store idle power tools out of the reach of

children and do not allow persons unfa-

miliar with the power tool or these instruc-

tions to operate the power tool. Power tools

are dangerous in the hands of untrained us-

ers.

e) Maintain power tools. Check for misalign-

ment or binding of moving parts, breakage

of parts and any other condition that may

affect the power tool’s operation. If dam-

aged, have the power tool repaired before

use. Many accidents are caused by poorly

maintained power tools.

f) Keep cutting tools sharp and clean. Prop-

erly maintained cutting tools with sharp cutting

edges are less likely to bind and are easier to

control.

g) Use the power tool, accessories and tool

bits etc. in accordance with these instruc-

tions, taking into account the working con-

ditions and the work to be performed. Use

of the power tool for operations different from

those intended could result in a hazardous

situation.

5) Service

a) Have your power tool serviced by a quali-

ed repair person using only identical re-

placement parts. This will ensure that the

safety of the power tool is maintained.

ADDITIONAL SAFETY INSTRUCTIONS FOR

ABRASIVE CUTTING-OFF OPERATIONS

CUT-OFF MACHINE SAFETY WARNINGS

a) The guard provided with the tool must be

securely attached to the power tool and po-

sitioned for maximum safety, so the least

amount of wheel is exposed towards the

operator. Position yourself and bystanders

away from the plane of the rotating wheel.

The guard helps to protect operator from broken

wheel fragments and accidental contact with

wheel.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach MT140 in the language / languages: English, German, French as an attachment in your email.

The manual is 2,59 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach MT140 Manual

Product: