782298
27
Zoom out
Zoom in
Previous page
1/152
Next page
27
Depth adjustment normal Fig. 6.1
Sawing function 5 mm below the table top. (separate
work pieces.)
Depth stop (1) housing-adjacent.
Stop screw (2) is used.
Setscrew (3) has no function.
Depth adjustment variable Fig. 6.2
Sawing function above the table top. (covered cuts)
Set depth stop (1) to the outside.
Set the setscrew (3) to the desired measurement and
secure it with the counternut (4).
Make a test cut.
Stop screw (2) is not used.
Carrying the Tool
• Loosenthemitrelockknobandturnthetableallthe
way to the right. Lock the table at 45° mitre angle.
• Push thecutting headbackwards andlock the car-
riage.
• Lowerthecuttingheadandpushinthelockpin.
• Carrythismitresawwiththebuilt-incarryhandleand
the side of the base.
Replacing of the saw blades, Fig. 7
Warning: Before replacing saw blades the switch must be
turned off and the mains plug must be disconnected from the
mains socket in order to avoid injuries by accidental start
up of the machine.
• Disconnectthemainsplug.
• Setthesawingunittoposition“mitreoperation”.
•Unlockthemovablesawbladecover(7)bypressing
the blocker 3 (Fig. 1).
• Whendoingsoliftthesawbladecover(7)tofreethe
saw blade (8).
• PushthesawbladeblockerA(g.7.1)untilthesaw
blade locks in place.
• Looseningofthesawbladexingscrewwiththeprovid-
ed socket wrench (B) (Attention, left-hand thread).
• Removescrewandsawbladeange.
• Removethesawbladecarefully.Attention:Dangerof
injuries from the saw blade.
• Setthenewsawbladeontheinnersawbladeange
observing the correct size and rotational direction of
the saw blade.
• Attachtheoutersawbladeangeandtightendiescrew
firmly.
• Setthesawbladecoverbacktothecorrectposition.
Réglage de profondeur normal (Fig. 6.1)
Position de la scie à 5 mm au-dessous du plateau de la
table. (séparer les pièces à usiner).
Butée de profondeur (1) appuyée sur le boîtier.
La vis de butée (2) est en utilisation
la vis de réglage (3) n’a pas de fonction.
Réglage de profondeur amovible (Fig. 6.2)
Fonctionnement de la scie au-dessus du plateau de la
table. (Coupes couvertes)
Régler la butée de profondeur (1) vers l’extérieur.
Régler la vis de réglage (3) sur la position
souhaitée, fixer avec le contre-écrou (4).
Effectuer une coupe d’essai.
La vis de butée (2) n’est pas utilisée.
Transport de la scie
• Desserrerlamolettedeblocaged’ongletetfairepivo-
ter le plateau vers la droite aussi loin qu’il peut aller.
Bloquer le plateau à un angle d’onglet de 45°.
• Pousserlatêtedecoupeenarrière,puisverrouillerle
chariot.
• Abaisserlatêtedescieetenclencherlagoupillede
sécurité.
• Transporterlascieparlapoignéedetransportincor-
porée et le côté du socle.
Remplacement de la lame (Fig. 7)
Avertissement : Avant le remplacement de la lame, il convient
de placer l’interrupteur sur arrêt et débrancher la fiche d’ali-
mentation de la prise de courant pour éviter des blessures
en cas de démarrage intempestif de la machine.
• Débrancherlached‘alimentation.
• Mettrelegroupedecoupeenposition« tronçonna-
ge ».
•Déverrouillerlaprotectionmobiledelalamedescie
(7) en appuyant sur le verrouillage 3 (Fig. 1).
• Enmêmetempssouleverlaprotectiondelalamede
scie (7), de sorte que la lame de scie (8) soit déga-
gée.
• AppuyersurleverrouillagedelalamedescieA(Fig.
7.1) jusqu’à ce que la lame de scie s’enclenche.
• Desserrerlavisdexationdelalamedescieàl’aidede
la clé à douille fournie (B) (Attention filet à gauche).
• Enleverlavisetlabridedelalamedescie.
• Retirerprudemmentlalamedescie.Attention:Risque
de blessures par la lame de scie.
• Placerunelamedescieneuvesurlabrideintérieure
de la lame de scie, tenir compte de la bonne dimension
et du sens de rotation de la lame de scie.
• Poserlabrideextérieuredelalamedescieetserrer
fermement la vis.
• Reposerlaprotectiondelalamedescieenrespectant
la bonne position
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach MSS 10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach MSS 10 in the language / languages: English, German, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5.96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info