782298
21
Zoom out
Zoom in
Previous page
1/152
Next page
21
and with an earthed type socket that fits the plug of this
machine at the other end.
Mounting the Tool
Note:
We highly recommend that you bolt this mitre saw se-
curely to a work bench to gain the maximum stability of
your machine.
• Locateandmarkthefourboltholesonthebench.
• Drillthebenchwithaø10mmdrillbit,
• Boltthemitresawontothebenchwithbolts,washers
and nuts. Note that these fasteners are not supplied
with the machine.
Operating the Tool
WARNING! Never connect the plug to the power source outlet
until all Installations and adjustments are completed and
you have read and understood the safety and operational
instructions.
Basic Pullover Mitre Saw Operations
• Alwaysusetheclamp17toholdtheworkpiecermly.
2 holes are provided for the clamp.
• Alwayspositiontheworkpieceagainstthefence.Any
piece that is bowed or warped and cannot be held flat
on the table or against fence may trap the blade and
should not be used.
• Neverplacehandsnearthecuttingarea.Keephands
outside the ”No Hands Zone” which includes the entire
table and is labelled by ”No Hands” symbols.
WARNING! To avoid injury from materials being thrown, un-
plug the saw to avoid accidental starting, and then remove
small materials.
Chop Cut (Fig. 6)
• Forchopcutting,slide thecuttingheadtotherear
position as far as it will go, and lock the carriage 1 by
the lock handle 2.
courant et, à l’autre extrémité, d’une fiche femelle avec
mise à la terre, qui s’enfiche dans la scie.
Montage de la scie
N. B.:
Il est vivement recommandé de boulonner la scie à un
établi pour lui assurer le maximum de stabilité.
• Repéreretmarquerl’emplacementdesquatretrousde
fixation sur l’établi.
• Percer les trous dans l’établi avec un foret de 10
mm.
• Boulonnerlascieàl’établiàl’aidedeboulons,ron-
delles et écrous (non fournis avec la scie).
Mode d’emploi
ATTENTION! Ne pas enficher la fiche dans une prise de cou-
rant avant d’avoir terminé toutes les étapes de l’installation
et du réglage et d’avoir lu et compris les consignes de sé-
curité et le mode d’emploi.
Consignes générales
• Toujoursutiliserleserre-joint17pourimmobiliserla
pièce à scier. 2 trous sont prévus pour le serre-joint.
• Toujoursplacerlapièceàcoupercontreleguide.Ne
pas utiliser de pièce cintrée ou tordue ou de pièce qu’il
est impossible de maintenir à plat sur le plateau ou
contre le guide, car elle risque de bloquer la lame.
• Nejamaisplacerlesmainsdanslazonedecoupe,qui
comprend l’ensemble du plateau et est indiquée par
des symboles „Pas de mains”.
ATTENTION! Pour éviter d’être blessé par des projections de
matériaux, débrancher la scie pour l’empêcher de se mettre
en marche accidentellement et enlever les petits morceaux
de matériaux.
Coupe de refend (Fig. 6)
• Pourlacoupederefend,faireglisserlatêtedecoupe
vers l’arrière aussi loin qu’elle peut aller et bloquer le
chariot 1 à l’aide de la manette de blocage 2.
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach MSS 10 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach MSS 10 in the language / languages: English, German, Danish, French, Italian, Polish, Portuguese, Swedish, Turkish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 5.96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info