23GB
8. Working instructions
Operation
• DO NOT SMOKE while refueling or operating equip-
ment.
• DO NOT TOUCH or let your hands or body come in
contact with a hot mufer or spark plug wire.
• DUE TO THE DANGER of exhaust fumes, never ope-
rate blower in a conned or poorly ventilated area.
• Use the tool only in broad daylight or in well-lit conditions.
• Do not underestimate the forces involved. Make sure
you stand squarely and keep your balance at all times.
• If possible, avoid using the tool on wet grass.
• Ensure that you maintain a steady foothold particularly
while working on slopes.
• Always walk. Never run.
• Always keep the ventilation opening clean.
• Never direct the blow hole at persons or animals.
• The machine may only be used at reasonable times
of the day, i.e. not in the early morning or late evening
when it will be a nuisance to other people. Permitted
times of use specied by local authorities must be
observed.
• The machine must be run at the lowest possible motor
speed required to carry out the work.
• Remove all foreign objects with a rake and brush be-
fore starting any blowing work.
• Where conditions are dusty, dampen the surface a little
or use a sprinkler attachment.
• Use the full-length blower nozzle extension so that the
air current can work near to the ground.
• Watch out for children, pets, open windows etc. and
blow the foreign objects safely away from them.
• Never feed hard objects such as stones, bottles, cans
or pieces of metal into the Blower. They can cause
damage to the machine and possibly injury to the ope-
rator and bystanders.
• Never operate the appliance with defective guards or
shields, or without safetydevices, for example debris
collector in place
• Do not expose the hot engine to ammable materials
• The Blower can be used to blow debris from patios,
paths, driveways, lawns, bushes and borders.
• Alternatively hold nozzle just above the ground and
swing the machine from side to side, moving forwards
and direct the nozzle at the debris to be cleared.
• Blow the debris into a convenient heap
9. Maintenance
Injury warning!
Always wear protective gloves when working on or
around cutting tools.
Change and clean the spark plug (Fig3)
Check the spark plug air gap at least once a year or when
the engine starts poorly. The correct gap between ignition
ag and ignition contact is 0.25“/0.63 mm.
• Wait until the engine has cooled down completely.
• Pull the spark plug cap off the spark plug, and use
the supplied spark plug wrench to remove the spark
plug by turning.
• When the electrode is severely worn out or reveals a
strong incrustation, the spark plug must be replaced
with an equivalent plug.
• A strong incrustation of the spark plug can be caused
by: Amount of oil is too high in the gasoline mix, poor
oil quality, old gasoline mix, or plugged up air lter.
• Screw the spark plug by hand completely into the th-
read. (Avoid jamming it)
•
• Use the supplied spark plug wrench to tighten the
spark plug.
• When using a torque wrench, the tightening torque
is 12-15 Nm.
• Plug the spark plug socket correctly on the plug.
Clean the air lter
Soiled air lters reduce the engine power by supplying
too little air to the carburetor. Dust and pollen plug up
the pores of the lter made of foamed plastic. Regular
checks are therefore essential.
• Unclip the air lter cover and remove the sponge lter
element.
• To avoid objects falling into the air tank, replace the
air lter cover.
• Wash the lter element in warm soap water, rinse and
allow drying naturally.
Important: Never clean the air lter with petrol or inam-
mable solvents.
In order not to shorten the service life of the engine, a
damaged air lter must be replaced at once.
Warning!
Never run the engine without the air lter element
installed.
FUEL FILTER
Inside the fuel tank there is a lter which prevents im-
purities from entering the engine. The lter should be
replaced once a year by your Retailer.
Injury warning!
Always wear protective gloves when working on or
around cutting tools.
