782052
14
Zoom out
Zoom in
Previous page
1/120
Next page
14 english
Any functional disorders, especially those affecting
the safety of the machine, sholud terefore be recti-
ed immediately.
The scheppach wood turner has been constructed
exclusively for use with wood.
Any other use exceeds authorization. The manufac-
turer is not responsible for any damages resulting
from unauthorized use; risk is the sole responsibility
of the operator.
The safety, work and maintenance instructions of
the manufacturer as well as the technical data given
in the calibrations and dimensions must be adhered
to.
Relevant accident prevention regulations and other,
generally recognized safety-technical rules must
also be adhered to.
The machine may only be used, maintained, and
operated by persons familiar with it and instructed in
its operation and procedures. Arbitrary alterations
to the machine release the manufacturer from all re-
sponsibility for any resulting damages.
The machine may only be used with original acces-
sories and tools made by the manufacturer.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial appli-
cations. Our warranty will be voided if the equipment
is used in commercial, trade or industrial businesses
or for equivalent purposes.
m Remaining hazards
The machine has been built using modern tech-
nology in accordance with recognized safety
rules. Some remaining hazards, however, may
still exist.
Only process selected woods without defects such
as: Branch knots, edge cracks, surface cracks.
Wood with such defects is prone to splintering and
hazardous.
Wood which is not correctly glued can explode
when being processed due to centrifugal force.
Trim work piece to a rectangular shape, center and
correctly secure before processing. Unbalanced
work pieces can be hazardous.
Injuries can occur when feeding work pieces if tool
supports are not correctly adjusted or if turning tools
are blunt. Sharp turning tools which are free of de-
fects are necessary for professional turning.
Long hair and loose clothing can be hazardous
when the work piece is rotating. Wear personal pro-
tective gear such as a hair net and tight tting work
clothes.
Saw dust and wood chips can be hazardous. Wear
pesonal protective gear such as safety goggles and
a dust mask.
The use of incorrect or damaged mains cables can
lead to injuries caused by electricity.
Even when all safety measures are taken, some re-
maining hazards which are not yet evident may still
be present.
Remaining hazards can be minimized by following
the instructions in „Safety Precautions“, „Proper
Use“ and in the entire operating manual.
Assembly (Fig. 2 – 5)
Your drilling machine is subassembled for technical
reasons involved with packaging.
Fig. 2 Slightly screw the frame feet in pairs with the
upper frame angle (each 3 neck bolts M8 x 12 with
washer and nut), put on sole plates.
Fig. 3 Screw the bottom chassis with the frame feet
also only hand-tight (each 2 neck bolts M8 x 12 with
washer and nut).
Place the frame on an even surface.
Fig. 4 Place the drilling machine onto the frame and
rmly screw with the 8 Allen screws ;8 x 35, with
spring washer and nut.
Finally tighten all the screws of the frame rmly.
Fig. 5 Insert the switch from inside into the frame
foot and screw on with the Phillips head screw M4
with washer and nut.
Start-up
Observe the safety notes in the operating instruc-
tions before operating the machine.
Remove the tensioning spindle or the chuck from
the spindle in addition to any step-up tools before
rst operating the machine!
Reversing switch, Fig. 6
Your turning machine is equipped witha reversing
switch. The motor is always switched on and off using
the operating switch. I = green; 0 = red.
The reversing switch is merely a selector for the direc-
tion of rotation. You can change the direction of rota-
tion from anticlockwise to clockwise as you
require.
Note: The speed setting can only be done when en-
gine is running.
For safety reasons, it is not possible to switch directly
from anticlockwise to clockwise when the motor is
running. When the reversing switch is in 0-position it
switches the motor off, which must be switched back
on using the green switch.
Speed adjustment Fig. 7
The speed can only be adjusted during work.
The correct number of revolutions is visible on the
speed diagram located on the headstock. The speed
diagram is intended for medium-hard dry woods.
The appropriate speed is based on various factors
such as:
type and compostion of woods
seasoned, dry woods
diameter and length of workpieces
squared or unbalanced woods
width of pre-worked, balanced workpieces
wood turner tools and technique
workpieces out of glued wood
Successful wood turning does not result from high
speeds, but rather, from correct use of the machine.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach Lata 5.0 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach Lata 5.0 in the language / languages: All languages as an attachment in your email.

The manual is 6.71 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info