782508

Scheppach KP-210 Bamato Manual

29
Zoom out
Zoom in
Previous page
1/48
Next page
29
GB
B
AMAT
O
Bavarian Machine Tools
If the carbon is worn to a length of 6 mm, or if the
spring or contact wire are burned or damaged, it is
necessary to replace both brushes. If the brushes are
found to be usable following removal, it is possible to
reinstall them.
Service information
Please note that the following parts of this product are
subject to normal or natural wear and that the follow-
ing parts are therefore also required for use as con-
sumables.
Wear parts*: Carbon brush, saw blade, battery, table
insert, sawdust bag, V-belts
* Not necessarily included in the scope of delivery!
11. Storage
Store the device and its accessories in a dark, dry
and frost-proof place that is inaccessible to children.
The optimum storage temperature is between 5 and
30˚C.
Store the electrical tool in its original packaging.
Cover the electrical tool in order to protect it from
dust and moisture.
Store the operating manual with the electrical tool.
12. Electrical connection
The electrical motor installed is connected and
ready for operation. The connection complies
with the applicable VDE and DIN provisions.
The customer‘s mains connection as
well as the extension cable used must al-
so comply with these regulations.
• The product meets the requirements of EN
61000-3-11 and is subject to special connection
conditions. This means that use of the product at
any freely selectable connection point is not al-
lowed.
• Given unfavorable conditions in the power supply
the product can cause the voltage to uctuate tem-
porarily.
• The product is exclusively intended for use at con-
nection points that have a continuous current-car-
rying capacity of at least 100 A per phase.
• As the user, you are required to ensure, in consul-
tation with your electric power company if neces-
sary, that the connection point at which you wish
to operate the product meets the specied require-
ments.
Important information
In the event of an overloading the motor will switch
itself off. After a cool-down period (time varies) the
motor can be switched back on again.
• Important! The work to change and align the saw
blade (7) must be carried out correctly.
8.11 Using the laser (Fig. 3/19/20)
• To switch on: Move the ON/OFF switch of the la-
ser (34) to the “1” position. A laser line is projected
onto the material you wish to process, providing an
exact guide for the cut.
• To switch off: Move the ON/OFF switch of the la-
ser (34) to the “0” position.
• Replacing the battery: Switch off the laser
(33). Remove the battery compartment cov-
er (36). Remove the batteries and replace with
new batteries (2 x 1.5 Volt Type LR 03 Micro,
AAA) Check that the battery terminals are po-
sitioned correctly when inserting new batter-
ies. Close the battery compartment (35) again.
8.12 Adjusting the laser (Fig. 21)
If the laser (33) ceases to indicate the correct cutting
line, you can readjust the laser. To do so, open the
screws (38) and set the laser by moving sideways to
that the laser beam strikes the teeth of the saw blade
(6).
9. Transport
• Tighten the set screw (26) in order to lock the ro-
tary table (14)
• Activate the release lever (3), press the machine
head (4) downwards and secure with the safety pin
(23). The saw is now locked in its bottom position.
• Fix the saw’s drag function with the locking screw
for drag guide (20) in rear position.
• Carry the equipment by the xed saw table (15).
• When reassembling the equipment proceed as de-
scribed under section 7.
10. Maintenance
m Warning! Prior to any adjustment, maintenance or
service work disconnect the mains power plug!
General maintenance measures
Wipe chips and dust off the machine from time to time
using a cloth. In order to extend the service life of the tool,
oil the rotary parts once monthly. Do not oil the motor.
When cleaning the plastic do not use corrosive prod-
ucts.
Brush inspection
Check the carbon brushes after the rst 50 operat-
ing hours with a new machine, or when new brushes
have been tted. After carrying out the rst check, re-
peat the check every 10 operating hours.
… 29 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach KP-210 Bamato at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach KP-210 Bamato in the language / languages: English, German, French as an attachment in your email.

The manual is 5.4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info