english 11
band. Wear proper gloves.
• Risk of injury due to starting saw band while switching
on the machine.
• The use of incorrect or damaged mains cables can lead
to injuries caused by electricity.
• Wear only close-fitting clothes. Remove rings, bracelets
and other jewelry.
• For the safety of long hair, wear a cap or hair net.
• Even when all safety measures are taken, some re-
maining hazards which are not yet evident may still be
present.
• Remaining hazards can be minimized by following the
instructions in „Safety Precautions“, „Proper Use“ and
in the entire operating manual.
Set-up, Fig. 9
Prepare the workplace where the machine is to be placed.
Insure sufficient room to allow safe work without malfunc-
tions. The machine is designed to operate in closed rooms
and must be placed stabily on firm level ground. Stability
is insured by attachment to the ground with 4 screws.
Transport
The machine may only be lifted and transported at the
identified points (see Figure 11). Never lift the machine
at the safety devices, the adjusting levers, or the sawing
table.
During the transport the saw blade protection must be in
the lowest position and near the table.
Never raise at the table!
Unplug the machine from the mains during transport.
Machine description
Due to its perfected design, the machine offers a versatile
application for processing wood and plastics in the work-
shop.
The upper and lower bandwheel is protected by a fixed
guard and an articulated cover. The non-cutting part of
the sawbelt above the table top is covered by a guard fixed
to the sawbelt guide, the latter being protected against
inadvertant opening by the fixed guard of the upper band
wheel. The non-cutting part of the sawbelt under the table
top is protected by a fixed cover.
The swivelling range of the table from 0° to +45° allows
versatile cutting possibilities (e.g.)
• Longitudinal cuts
• Cross cuts
• Diagonal cuts
• Curved and irregular cuts
• Cuts for dovetails and tenons
• On-edge cuts of squared beams
Please consult also the working hints in the operating in-
structions.
Assembly
Assembly tools
1 engineer’s wrench SW 10
1 hexagonal head spanner SW 3
1 hexagonal head spanner SW 6
Tabletop and the mounting angles are not mounted for rea-
sons of packaging technology.
Installation of the tabletop, Fig. 1
• Open the case cover, and set the slewing segments to
30°.
• Loosely screw the tabletop.
4 hexagon head cap screws M 6 x 12
4 serrated lock washers A 6,4
Fig. 1.1
Screw in the setting screw approx. 29 mm on the bottom
side of the table and fix it by hand.
Fig. 2 Adjusting the tabletop
Swivel the tabletop to the 0° position and tighten the
thumbscrew (A).
Align the tabletop parallel to the saw blade, tighten with 4
hexagonal screws at the swivel segment.
Loosen thumbscrew (A), align the table in the right angle
to the saw band adjust it with the setting screw (L), and
fix it with the nut.
– Use stop angle –
Set the scale pointer to 0 if necessary.
Fig. 2.1 Adjustment in the centre of the table insert
Loosen the 3 hexagon nuts (X) by approximately 2 turns,
and move the support with the table until the saw blade is
in the centre of the table insert. Then, tighten the hexagon
nuts again.
Assembly of the longitudinal limit stop, fig. 3
• Screw in 4 thumbscrews M6x12 each with one washer
and a spring washer to a length of approx. 5 mm into the
tabletop.
• Insert the guide tube until it stops at the table.
• Fasten the guide tube with a screw M 6 x 20, a washer
and a cup washer to the table (fig. 3.1).
• Tighten the screw so far that the guide tub can be moved
free of clearance; fix it next with the hexagonal nut.
• Tighten then the 4 thumbnuts.
Fig. 4
Place now the longitudinal limit stop onto the guide tube
on the right of the saw band and clamp it. The guide tube
must now be parallel to the table groove, a correction can
be performed by loosening both the cheese head screws ,
remove the protecting cap to do this.
Setting of the longitudinal limit stop fig. 5
Set the longitudinal limit stop onto the stop pipe on the
left side of the saw blade, measure now 50 mm from the
saw blade to the stop tube. The scale line on the magnify-
ing glass should now stand at 50 mm.
Readjust the scale if necessary.
Loosen thereby the Phillips Head Screw (K) of the scale
and set it to the dimension 50, retighten the Phillips Head
Screw.
– Close the protective cover –
m Commissioning
Before putting the machine into operation, carefully observe
the safety instructions.
When working with the machine, all protective devices and
guards must be fitted.
Saw band replacement, figure 6
Open protective cover with hexagonal head spanner SW
