Manual Scheppach KITY 439 (page 47 of 80) (English, German, French)

782080

Zoom out

Zoom in

1/80

DGB

7. BENUTZUNG DER MASCHINE

h. Abrichthobeln von Werkstücken

1. Hobeln eines Probestücks (34)

7. PUTTING THE MACHINE INTO OPERATION

h. Surface planing

1. Planing of a piece (34)

- Vor dem ersten Gebrauch wischen Sie das Anti-Korrosions-

mittel mit Petroleum von der Hobelwelle (Verwenden Sie kein

Benzin).

- Der Dickentisch (D) muss eingestellt werden um den

Absaugstutzen zu montieren (F). (33)

- fahren Sie den Dickentisch mit dem Handrad (M1) nach

oben, um den Absaugstutzen (F) unter dem Ausganstisch (B)

gut zu spannen.

- Kuppeln Sie den Einzugshebel für Bretter (Y) aus, damit

sich die Antriebswalzen nicht unnötig drehen.

- Um senkrechte Flächen und Kanten zu erhalten, justieren

Sie zuvor den Winkelanschlag auf 90°. (siehe «Einstellen des

Winkelanschlags»).

Wichtig : Vergewissern Sie sich vor Beginn der Arbeit, dass

das Holz keine Äste hat, um einen gehährlichen Rückschlag

zu vermeiden.Achten Sie auch darauf, dass die Oberfläche

desHolzes nicht zu sehr gewölbt ist.

- Legen Sie die «hohle» Oberfläche des Brettes auf den

Eingangstisch (A).

- Stellen Sie den Hobelwellenschutz (G) ein (siehe «Einstel-

len des Hobelwellenschutzes»)

- Schieben Sie das Brett mit einer durchgehenden Bewegung

gegen die Hobelwelle, um Ungleichmäßigkeiten zu vermei-

den.

- Üben Sie an den Kontaktpunkten mit dem Tisch einen

Druck aus und drücken Sie mit der linken Hand den geho-

belten Anfang des Brettes auf den Ausgangstisch (B). Die

rechte Hand dient nur zum Schieben des Brettes.

- Verwenden Sie am Brettende den Schiebestock. (35)

- Wiederholen Sie den Arbeitsgang, bis eine sauber

gehobelte öberfläche entstanden ist.

- Am Ende des Durchgangs, kann das Brett auf den Ein-

gangstisch (A) zurückgeholt werden, indem man es über den

Hobelwellenschutz (G) gleiten lässt.

- Before the first use, wipe the anti-corrosion agent from the

cutter block with petroleum (do not use gasoline).

- The thicknessing table (D) must be set in order to fit the

suction connection (F). (33)

- Move the thicknessing table upwards with the hand wheel

(M1), in order to firmly clamp the suction connection (F)

underneath the ouput table (B).

- Disengage the feed lever for boards (Y) so the drive rollers

do not rotate without necessity.

- In order to get vertical surfaces and edges, first adjust the

angle guide to 90°. (see. «Setting the angle guide»)

Important : before starting work make sure that the wood

does not have any knots in order to avoid dangerous kick-

back. The work piece surface must also not be much curved.

- Put a board with the «hollow» surface on to the infeed table

(A).

- Set the cutter block guard (G). (see «setting the cutter block

guard»)

- Push the board smoothly against the cutter block in order to

avoid irregularities.

- Exerce a pressure where the board touches the table. With

your left hand, press the planed start of the board onto the

output table (B). The right hand only pushes the board.

- Use the stick at the end of the board. (35)

- Repeat the procedure until a clean planed surface is

obtained.

- At the end of the passage, the board can be returned to the

entry table (A) by letting it slide over the cutter block guard

(G).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach KITY 439 in the language / languages: English, German, French as an attachment in your email.

The manual is 1.83 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Scheppach KITY 439 Manual

Product: