781427

Scheppach HWW1300 Manual

26
Zoom out
Zoom in
Previous page
1/88
Next page
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
26 | GB
Damaged electrical connection cable
The insulation on electrical connection
cables is often damaged. This may have
the following causes:
• Passage points, where connection cables
are passed through windows or doors.
• Kinks where the connection cable has
been improperly fastened or routed.
• Places where the connection cables
have been cut due to being driven over.
• Insulation damage due to being ripped
out of the wall outlet.
• Cracks due to the insulation ageing.
Such damaged electrical connection ca-
bles must not be used and are life-threat-
ening due to the insulation damage.
Check the electrical connection cables
for damage regularly. Make sure that the
connection cable does not hang on the
power network during the inspection.
Electrical connection cables must comply
with the applicable VDE and DIN provi-
sions. Only use connection cables with
the marking „H05RN-F“.
The printing of the type designation on
the connection cable is mandatory. For
single-phase AC motors, we recommend
a fuse rating of 16A (C) or 16A (K) for ma-
chines with a high starting current (start-
ing from 3000 watts)!
AC motor 230 V~/ 50 Hz
Mains voltage 230 V~ / 50 Hz.
The mains connection and the extension
cable have to be three-core cables = P
+ N + SL. - (1/N/PE). Extension cables
up tp 25m long must have a minimum
cross-section of 1.5 mm². Mains fuse pro-
tection is 16 A maximum.
9. Initial operation
m IMPORTANT!
You must fully assemble the appliance
before using it for the rst time!
• Install the equipment on a solid and lev-
el surface.
• Unscrew the coarse lter screw (8) and
remove the coarse lter (9) as shown
in Figure 3. Now you can ll the pump
housing with water via the coarse lter
screw (8). Filling the intake line acceler-
ates the in take process.
• Assemble in reverse order.
• Open the discharge line.
• Connect the mains cable.
• Switch on the equipment with the power
switch (12) water can be suctioned in for
up to 5 minutes (max mum suction height).
• After pressure drop due to water con-
sumption switches the unit automatically
on (switch-on pressure approx. 1.5 bar)
• The domestic waterworks can be used
for domestic water supply in the inner
area also be permanently installed. To
avoid vibrations and noise should be
minimised. the pump with exible hose
lines connected to the pipe network will
be. Anti-vibration material is also rec-
ommended, z. e.g. a rubber layer, be-
tween pump and base to lay. Ensure a
stable Fixing of the container by means
of Screws that pass through the holes
t in the stand.
Electrical connection
The electrical motor installed is connect-
ed and ready for operation. The connec-
tion complies with the applicable VDE
and DIN provisions.
… 26 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach HWW1300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HWW1300 in the language / languages: English, German, French, Finnish as an attachment in your email.

The manual is 2.37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info