782084
19
Zoom out
Zoom in
Previous page
1/36
Next page
19
Transport
Pour transporter, nattacher le dispositif de relevage quau
ti, jamais aux dispositifs protecteurs, aux poignées de
réglage ou à la table de dégauchissage.
Pour le transport, débrancher la prise d’alimentation.
Lors du transport, le protecteur de l’arbre de rabotage
doit se trouver dans la position la plus basse.
Déballage de la machine
Vérifier dès la livraison, qu’aucune pièce nait été -
tériorée pendant le transport. En cas de réclamation,
informer aussitôt le livreur. Vérifier que la livraison soit
bien complète. En cas de réclamation, informer aussitôt
le vendeur.
La machine est expédiée dans un seul carton. Des acces-
soires supplémentaires doivent être localisés et identifiés
avant le début du montage.
Fig. 2
1. Raboteuse-dégauchisseuse
2. Butée de rabotage
3. Poignée
4. Manchon de prise d’air
Montage
Montage butée de dressage Fig. 3
Attention ! Avant tout travaux de rééquipement et de
montage, débrancher la fiche d’alimentation
Monter le support de dressage (A) avec 2 vis Allen demi-
rondes (B) M6 x20 mm et 2 rondelles de 6 mm (B) sur la
paroi latérale de la machine à raboter. Glisser le rail de
butée (C) avec les encoches dans les écrous pré-montés
et serrer ces derniers au moyen des 4 vis papillon (E).
Alignement de la butée de dressage Fig. 3
Régler la butée à un angle de 90 ° et la serrer avec la
vis à clé (H). Régler la vis à fente (F) jusqu’à la butée et
la bloquer avec l’écrou. Puis régler la butée sur 45° et
bloquer avec la vis à clé (H). Ensuite régler la vis Allen
(G) jusqu’à la butée et bloquer avec l’écrou.
Vérifier les angles à l’aide d’un échantillon et régler de
nouveau l’échelle (I) si cela est nécessaire.
Montage protection de l’arbre de rabot Fig. 5, 6
La vis à tête moletée (6) sert à soulever la protection de
l’arbre de rabot (1).
Transport
Do transportu, maszyna może być podnoszona wyłącznie za
podstawę. Nigdy nie należy jej podnosić za osłony, uchwyty
nastawcze lub stół strugarki /strugarki grubościowej.
Przed transportowaniem, należy wyjąć wtyczkę z gniazd-
ka.
W czasie transportu, osłona głowicy frezowej musi być usta-
wiona w najniższej pozycji.
Rozpakowanie maszyny
Sprawdzić zawartość pod kątem wystąpienia uszkodzeń
transportowych. W przypadku uszkodzenia, poinformować
natychmiast spedytora. Sprawdzić zawartość pod kątem
kompletności. Poinformować natychmiast dealera w przy-
padku brakujących części.
Kompletna maszyna jest wysyłana w pojedynczym pudełku
kartonowym. Wszelkie dodatkowe części, które mają być
dołączane do maszyny, muszą być zidentykowane przed
rozpoczęciem montażu.
Rys. 2
Maszyna do strugania wzdłużnego i grubościowego1
Prowadnica strugarki 2
Uchwyt 3
Złącze ssące 4
Montaż
Montowanie zderzaka krańcowego do przycinania Rys.
3
Uwaga! Urządzenie musi być odłączone od sieci w czasie
prac polegających na wymianie narzędzi lub montażu.
Zamocować wspornik przycinania (A) na bocznej ściance
maszyny do strugania wzdłużnego za pomocą 2 półokrą-
głych wkrętów z łbem sześciokątnym z gniazdkiem (B) M6
x20 mm i 2 podkładek 6 mm (B). Teraz wsuń szynę zatrzy-
mującą z rowkiem (C) w zamocowane wstępnie nakrętkach i
dokręć je za pomocą 4 śrub motylkowych (E).
Wyrównywanie zderzaka krańcowego do przycinania
Rys. 3
Ustawić zderzak krańcowy na kącie 90° i zacisnąć go na swo-
im miejscu za pomocą śruby rozporowej (H). Teraz umieścić
śrubę z rowkiem krzyżowym (F) na zderzaku krańcowym i
dokręcić nakrętką. Następnie ustawić zderzak krańcowy
na 45° i zacisnąć go na miejscu za pomocą śruby zacisko-
wej (H). Następnie, umieścić wkręt z łbem z sześciokątnym
gniazdkiem (G) na zderzaku krańcowym ii dokręcić go za
pomocą nakrętki.
Należy porównać oba wsporniki ze wzorem i dostosować
skalę, jeżeli jest to wymagane.
Montowanie osłony osi strugarki Rys. 5, 6
Śruba z łbem radełkowanym (6) służy do podnoszenia osło-
ny osi strugarki (1).
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach HT 1060 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HT 1060 in the language / languages: German, French, Polish as an attachment in your email.

The manual is 10.01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info