644558

Scheppach HS80 Manual

33
Zoom out
Zoom in
Previous page
1/288
Next page
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
GB | 33
8. Ret the saw blade guard (4) and adjust it (see
8.3).
m WARNING: Check the protective devices before
working with the saw again.
8.7 Fitting the parallel stop (g, 2, 15)
1. Fasten the holder (16) to the table with the help
of the locking knobs (15) and the clamping plates
(15a).
2. Make sure that the holder (16) is aligned parallel
to the saw blade (5). If necessary, readjust it with
the aid of the scale (38).
3. Slide the sliding block along the groove (37) in the
stop rail (17).
4. Fasten the stop rail (17) to the holder (16) with the
help of the screws (16a).
8.8 Fitting the transverse stop (g. 18)
1. Slide the transverse stop (2) in the groove (40) of
the saw table (1).
2. Loosen the turning handle (19).
3. Turn the transverse stop (2) until the arrow points
to the desired angle.
4. Retighten the turning handle (19).
8.9 Chip extraction (g. 13)
ATTENTION: Only operate the device with an extrac-
tion system.
Connect a suitable chip extraction system (not includ-
ed in the scope of delivery) to the suction port (36).
ATTENTION: Check and clean the suction channels
at regular intervals.
9. Handling the equipment
9.1 Switches (g. 1)
9.1.1 On/off switch (11)
• It is possible to switch the saw on by pressing the
green “I” button. Before starting sawing, wait until
the saw blade has reached its maximum speed.
• In order to switch the saw off again, it is necessary
to press the red “0” button.
9.1.2 Overload switch (10)
The device motor is protected against overload with
an overload switch (10).
In the event of the nominal current being exceeded,
the overload switch (10) switches the device off.
If this happens, proceed as follows:
• Let the device cool down for several minutes.
• Press the overload switch (10).
• Switch the device on by pressing the green “I” but-
ton.
9.2 Setting the cutting depth (g. 1)
The saw blade (5) can be adjusted to the required
cutting depth by turning the hand wheel (8).
• Counter-clockwise: Greater cutting depth
• Clockwise: Smaller cutting depth
Check the setting with a test cut.
9.3 Setting the angle (g. 14)
Angled cuts of 0°-45° to the left of the parallel stop (7)
can be carried out with the circular table saw.
m Before making every cut, check that no collision
can occur between the stop rail (17), transverse stop
(2) and the saw blade (5).
1. Loosen the locking handle (9).
2. Set the desired angle on the scale by turning the
hand wheel (8).
3. Lock the locking handle (9) at the desired angle
setting.
9.4 Using the parallel stop (g. 2, 15-17)
9.4.1 Stop heights (g. 15, 16)
• The stop rail (17) of the parallel stop (7) has two
guide surfaces at different heights.
• Depending on the thickness of the material to be
cut, the stop rail (17) must be used as shown in Fig.
15 for thick material (workpiece thickness exceed-
ing 25 mm) and as shown in Fig. 16 for thin material
(workpiece thickness below 25 mm).
9.4.2 Shifting the stop rail (g. 15, 16)
1. In order to move the stop rail (17) to the lower
guide surface, loosen the two screws (16a) to re-
lease the stop rail (17) from the holder (16).
2. Pull the stop rail (17) along the groove and out.
3. Turn the stop rail (17) and slide the sliding block
along the second groove (39).
4. Shifting to the higher guide surface must be car-
ried out in the same way.
9.4.3 Cutting width (g. 15, 16)
• The parallel stop (7) must be used when cutting
sections of wood lengthways.
• The parallel stop (7) can be mounted on both sides
of the saw table (1).
• The parallel stop (7) can be set to the required di-
mension with the aid of the scale (38) on the saw
table (1).
• Tighten the two locking knobs (15) to fasten the
parallel stop (7) in place.
• Perform a test cut to measure the width before cut-
ting the real workpiece. In this way you avoid inac-
curacies with the scale or the setting.
… 33 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach HS80 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HS80 in the language / languages: All languages as an attachment in your email.

The manual is 10.49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Scheppach HS80

Scheppach HS80 User Manual - English, German, Danish, French, Italian, Swedish, Finnish - 103 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info