782520

Scheppach HS120 Manual

43
Zoom out
Zoom in
Previous page
1/264
Next page
43
• Le produit est exclusivement prévu pour l’utilisation
aux points de raccordement
a) qui ne dépassent pas une impédance de réseau
maximale autorisée de «Z» ou
b) qui ont une intensité admissible du courant perma-
nent d’au moins 100 A par phase.
• En tant qu’utilisateur, vous devez vous assurer, si
nécessaire en consultant votre entreprise d’électricité
locale, que le point de raccordement avec lequel vous
voulez exploiter le produit, répond à l’une des deux exi-
gences a) ou b).
Maintenance
Avertissement : Avant d’effectuer des travaux de réglage,
éteignez la machine et tirez la prise de courant.
Gardez le mode d’emploi à proximité de la machine.
Maintenez la machine propre.
Lors du nettoyage, portez des lunettes de protection.
Attention : Ne pas nettoyer les parties en plastique du
plateau avec des produits agressifs. Nous recommandons
un produit de vaisselle sur un tissu humide. La machine
ne doit pas entrer en contact avec de l’eau.
• Vérifier le bon état de la lame de scie à intervalles régu-
liers. N’employer que des lames de scie bien aiguisées
qui ne sont pas fissurées ni déformées. Se servir uni-
quement d’outils qui se conforment à la norme euro-
péenne EN 847-1.
• Remplacer la garniture de la fente d’insertion dans la
table dès qu’elle est usée.
• Toujours conserver la surface de la table exempte de
résine.
• Nettoyer systématiquement l’espace interne de la ma-
chine, tels que le segment denté et le pignon du dispo-
sitif d’inclinaison, pour en enlever les résidus de bois et
de copeaux.
• Retirer les bouchons de sciure de bois qui risquent
d’obstruer l’évacuateur.
Faire réparer l‘outil électrique par un électricien spécia-
lisé.
Cet outil électrique est conforme aux dispositions de sé-
curité en vigueur. Les réparations ne doivent être menée
à bien que par un électricien spécialisé qui utilisera des
pièces de rechange d‘origine. Sinon, l‘utilisateur risque
l‘accident.
• The product is intended solely for use at connection
points that
a) do not exceed a maximum permitted supply imped-
ance “Z”, or
b) have a continuous current-carrying capacity of the
mains of at least 100 A per phase.
• As the user, you are required to ensure, in consulta-
tion with your electric power company if necessary, that
the connection point at which you wish to operate the
product meets one of the two requirements, a) or b),
named above.
Maintenance
Warning: Turn off the machine and disconnect from the
power supply before conducting maintenance work or set-
tings.
Store the manual close to the machine.
Keep the machine clean.
Wear goggles when cleaning the machine.
Caution: Do not clean synthetic components of the bench
using aggressive cleaning agents. We recommend a mild
dish washing liquid. The machine must not get into con-
tact with water.
• Check the saw blade regularly. Use only well-sharp-
ened, crack-free and not distorted saws. Use only tools
that comply with the European standard EN 847-1.
• Exchange immediately table lining that run out.
• Always keep table surface nonresinous.
• Clean regularly the inner section of the machine, like
tooth segement and pinion of the oscillating device, of
wood and chip rests.
• Remove possible sawdust blockages at the discharge.
Have your electric tool repaired by a qualified electrician.
This electric tool conforms to the applicable safety
regulations. Repairs may only be performed by an electri-
cian using original spare parts. Otherwise accidents can
occur.
… 43 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach HS120 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HS120 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 9.4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info