782520

Scheppach HS120 Manual

13
Zoom out
Zoom in
Previous page
1/264
Next page
13
• Lower the cover onto the workpiece during every work-
ing operation. It must stand horizontal above the saw
blade.
• Always use a push-stick for longitudinal cuts
of narrow workpieces (less than 120 mm). The
push-stick must be used to prevent you from hav-
ing to work with your hands near the sawblade.
Stop the machine to repair a failure or remove pieces
of wood which have become jammed. Disconnect the
mains plug.
• Use the push stick or the feed lever for sliding the
wood, to guide it safely past the saw blade.
• Switch the machine off and pull power supply plug
when rectifying any malfunctions.
• The table insert must be renewed when the saw slot is
worn down. Pull power supply plug.
• Before the machine is put into operation it must be
connected to a dust extractor with a flexible, non-flam-
mable suction hose. The suction should switch on auto-
matically when the machine is switched on.
• When leaving the work place, switch the motor off. Pull
the power supply plug.
• Cut off the external power supply of the machine or
plant even if only minor changes of place are envisaged.
Properly reconnect the machine to the supply mains
before recommissioning.
• Connection and repair work on the electrical installation
may be carried out by a qualified electrician only.
• All protection and safety devices must be replaced after
completing repair and maintenance procedures.
Accessories
Only purchase accessories from your authorised special-
ised dealer.
m Use only as authorized
The machine corresponds to the valid EC guideline.
CE tested machines meet all valid EC machine guidelines as
well as all relevent guidelines for each machine.
• The machine has been built in accordance with state-
of-the-art standards and the recognized safety rules.
Nevertheless, its use may constitute a risk to life and
limb of the user or of third parties, or cause damage to
the machine and to other material property.
• The circular saw bench is constructed exclusively for
the sawing of wood. The required saw blade should be
inserted according to the cut type and the wood type
(solid wood, chip board or plywood).
• Les lames de scie circulaire en acier rapide à haute
performance ne doivent pas être utilisées.
• Le coin séparateur est un dispositif de protection im-
portant, qui guide la pièce et empêche que l’entaille
ne se referme derrière la lame, ce qui évite un retour
de pièce.
• Descendre le carter de protection sur la pièce lors de
chaque passe. Celui-ci doit se trouver à l’horizontale
au-dessus de la lame.
• Lors d’une coupe longitudinale d’une pièce – inférieure
à 120 mm – il est indispensable d’utiliser une tige de
poussée. L’utilisation de cette tige est nécessaire pour
éviter que les mains se trouvent à proximité de la lame
de scie.
• Utilisez un poussoir à bois ou une poignée-poussoir
pour pousser la pièce à usiner contre la lame de scie
en toute sécurité.
• Pour pallier à une cause de dérangement, arrêter la
machine, débrancher la prise.
• Si la lumière de passage de lame est détériorée, rem-
placer la partie rapportée. Retirer la prise.
• Avant d’être mise en service, la machine doit être rac-
cordée à une installation d’aspiration au moyen d’une
conduite d’aspiration flexible et difficilement inflam-
mable. L’aspiration doit s’enclencher automatiquement
lorsque la machine est mise en service.
• Lorsque l’on s’éloigne de l’emplacement de travail,
arrêter le moteur et débrancher la prise.
• Même pour des changements de place peu importants,
séparer la machine ou l’installation de toute alimenta-
tion en énergie venant de l’extérieur! Avant la remise en
service, rebrancher la machine sur le réseau!
• Les branchements et réparations de l’équipement élec-
trique ne doivent être effectués que par un spécialiste
de l’électricité.
• Une fois les travaux de réparation et de maintenance
achevés, tous les dispositifs de protection et de sécurité
doivent être remontés immédiatement.
Accessoires
A acheter uniquement auprès de votre revendeur spécia-
lisé.
m Utilisation conforme
La machine correspond aux normes en vigueur dans la Com-
munauté Européenne.
• La scie circulaire est définié en tant que machine semis-
tationnaire suivant pr EN 1870-1.
• Pour le transport, tenir fermement chaque extrémité du
plateau à deux mains et soulever l’ensemble.
• Si vous n’utilisez pas le support d’origine, la machine
doit être posée sur un support plane et stable. La hau-
teur de travail doit être au minimum de 800 mm.
• Le poste de travail se trouve à l’avant de la machine, à
gauche de la lame de scie.
… 13 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach HS120 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HS120 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 9.4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info