782563
37
Zoom out
Zoom in
Previous page
1/72
Next page
www.scheppach.com / service@scheppach.com / +(49)-08223-4002-99 / +(49)-08223-4002-58
GB | 37
9. Connect the machine stand part 2 (24b) with the
machine stand part 3 (24c) using two Phillips
screws M5 x 40 mm (D) and two nuts M5 (M) on
each side. (g. 12)
10. Fit two at end caps (N) on the ends of machine
stand part 3 (24c).
11. Connect the machine stand part 3 (24c) with the
machine stand part 6 (24f) using one coach bolt
M8 x 78 mm (A), one spacer (J) and one nut M8
(K) on each side. (g. 13)
NOTE: Do not over-tighten the screws. The parts
must be able to move freely.
12. Connect the machine stand part 4 (24d) with the
machine stand part 3 (24c) using one coach bolt
M8 x 78mm (A), one spacer (J) and one nut M8
(K) on each side. (g. 14)
13. Now connect both wheels (13) with the machine
stand part 4 (24d) using the wheel screws (P) as
shown in g. 15.
14. Turn the machine so that it rests on the machine
stand (24).
15. Release the locking latch (14) and fold up the ma-
chine stand until the locking pin engages into the
locking latch (14).
9.2 Removing the table inlay (g. 16)
1. Set the saw blade (1) to the max. cutting depth,
move to the 0° position and lock in place (see 11.2).
2. Loosen the xing screw (4a) by turning it a quarter
turn counterclockwise.
3. Remove the table inlay (4) from the saw table (5).
9.3 Riving knife
m WARNING
Danger of injury due to unexpected start-up of the
machine
- Remove the mains plug from the socket.
You need to remove the table inlay (4) before you can
install and adjust the riving knife (3).
9.3.1 Insertng and adjusting the riving knife (g.
17 + 18)
1. Loosen the xing screw (3a). (g. 17)
2. Push the riving knife (3) into the holder.
NOTE: This step is not necessary if the riving knife
(3) is already inserted.
3. Align the riving knife (3) such that
a) the distance between the saw blade (1) and the
riving knife (3) is max. 5 mm (g. 18) and
b) the saw blade (1) is parallel to the riving knife (3).
3. Tighten the xing screw (3a) again.
9.4 Fitting the table inlay (g. 16)
1. Place the table inlay (4) in the recess.
2. Tighten the xing screw (4a) by turning it a quarter
turn clockwise.
You require the following for assembly:
1x open-ended spanner 10/13 mm (26)
1x ring spanner 10/21 mm (27)
(included in the scope of delivery)
1x Phillips screwdriver
1x Allen key 5 mm
(not included in the scope of delivery)
Place all supplied parts on a at surface.
Group equal parts.
NOTE:
If connections are secured with a screw (round-
head or hexagon), hexagon nuts and washers, the
washer must be tted under the nut.
Insert screws each from outside to inside. Secure
connections with nuts on the inside.
Tighten the nuts and screws during assembly only
until they are unable to fall o󰀨. If you tighten the
nuts and screws fully before nal assembly, it is not
possible to complete the assembly.
9.1 Fitting the machine stand (g. 5 - 15)
1. Turn the machine over and place it on a clean sur-
face. (g. 5)
2. Fasten the two machine stand parts (24f) on the
machine housing using two Allen screws M6 x 53
mm (B), two large washers (I) and two nuts M6 (L)
each. (g. 6)
3. Fit both round end caps (O) on the ends of the
machine stand parts (24f). (g. 6)
4. On the other side, t both at end caps (N) on the
ends of the machine stand parts (24f). (g. 6)
5. Connect the machine stand part 4 (24d) with the
machine stand part 5 (24e) using two Phillips screws
M5 x 50 mm (C) and two nuts M5 (M). (g. 7)
6. Connect the machine stand part 4 (24d) with the
machine stand part 1 (24a) using two coach bolts
M8 x 78 mm (A), two spacers (J) and two nuts M8
(K). (g. 8)
NOTE: Do not over-tighten the screws. The parts
must be able to move freely.
NOTE: Make sure that the locking latch (14) on ma-
chine stand part 4 (24d) is on the same side as the
locking pin on machine stand part 1 (24a). (g. 9)
7. Fit two at end caps (N) on the ends of machine
stand part 4 (24d). (g. 9)
8. Connect the machine stand part 4 (24d) with the
machine stand part 6 (24a) using two coach bolts
M8 x 78 mm (A), two spacers (J) and two nuts M8
(K). (g. 10 + 11)
NOTE: Do not over-tighten the screws. The parts
must be able to move freely.
NOTE: Make sure that the locking latch (14) is on
the same side as the on/o󰀨 switch (15).
37


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach HS116 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HS116 in the language / languages: English, German, French as an attachment in your email.

The manual is 6.03 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info