644538
16
Zoom out
Zoom in
Previous page
1/21
Next page
Seite:16
Motor-brake appliance
The brake slowes down the motor of the saw shaft within 10 seconds. The electrical braking is interrupted after maximum
14 seconds.
In case the braking takes more than 10 seconds the machine should not be used again, as the brake is defective. The
machine implicitly needs to be disconnected from the power supply. Only an electronic specialist should be instructed to
repair this malfunction.
The electrical motor is dimensioned for operating mode S 6 - 40 %.
S6 = pass operation with load exposure
40% = related to 10 min. 4min. load; 6min. pass operation
If the motor gets overcharged, it automatically switches off, as a winding thermal switch is built in in the winding of the
motor. After a cool-down period (time varies) the motor can be switched on again.
Defective electrical power supply cords
Electrical power supply cords often suffer insulation damages.
Possible causes:
•Pressure spots, when power supply cords are being led through windows or doors.
•Buckling spots by incorrect attachment or guidance of the power supply cords.
•Cuttings by driving over a power supply cord.
•Insulation damages through pulling out of the socket.
•Cracks in worn-out insulation.
Such defective electrical power suplly cords should not be used and are extremely dangerous because of the insulation
damage.
Check electrical power supply cords on damages on a regular base. Please pay attention that upon checking the power
supply cord is not plugged in. Electrical power supply cords have to comply with the relevant VDE and DIN-regulations. Only
use power cables with the qualication H 07 RN. The type denomination should be imprinted.
There has to be an imprint of the type denomination on the connection cable.
•Extension cables must be up to 25 m long, have a cross cut of 1.5 square millimeter, be over 25 m length, and have a
minimum 2.5 square millimeter.
•The powersupply should be 16 A.
Rotary current motor
•The power supply has to be 380-420 Volt / 50 Hz.
•The power supply and the extension cables must be 5-fold leads = 3 P + N + SL.
•Extension cables must have a minimum cable cross section of 1.5 square millimeter.
•The power supply should be maximum 16 A.
•In case of connection to the power supply or moving site the rotary direction should be checked, otherwise the polarity has
to be changed.
Alternating current motor
•The supply voltage hast to be 220-240 Volt / 50 Hz.
•Extension cables must be up to 25 m long, have a cross cut of 1.5 square millimeter, be over 25 m long, and have a mini-
mum 2.5 millimeter.
•The power supply should be 16 A.
Connections and repairs of the electrical equipment should only be carried out by an electrical specialist.
In case you have further questions, please specify the following:
•Motor manufacturer
•Current type of the motor
•Information of the machine type label
•Information of the switch type label
If you send the motor back, always return the complete power unit with electro-control.
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Scheppach HS 720 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Scheppach HS 720 in the language / languages: English, German as an attachment in your email.

The manual is 3,54 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info